DEWALT DCS575 원형톱 수리 및 유지보수 매뉴얼
DEWALT DCS575 60V MAX 7-1/4인치 무선 원형톱. 이 가이드를 사용하기 전에 등급 라벨에서 DCS575 및 유형을 확인하십시오. 이 도구는 60V MAX FL을 사용합니다.
$29.99
마지막 업데이트 Aug 17, 2026, 7:51 AM
Manual information
이 매뉴얼에 대하여
DEWALT DCS575 60V MAX 7-1/4인치 무선 원형톱. 이 가이드를 사용하기 전에 등급 라벨에서 DCS575 및 유형을 확인하십시오. 이 도구는 60V MAX FL을 사용합니다.
보고된 수리 성공률 0%
전체 수리 매뉴얼 받기 — US$250–US$290 절약
$29.99
전체 매뉴얼 포함 내용
- root cause analysis
- tools needed
- step-by-step repair procedure
- diagrams
- exploded views
- post-repair checks
목차 미리보기
- 먼저 읽기
- 기술 사양
- 이 기기가 실제로 작동하는 방식
- 빠른 진단 표
- 부품 및 제어장치
- 증상에서 원인으로
- 고장 모드 FM-01부터 FM-16까지
- 부품 및 키트 분류기
- 16가지 고장 모드
- Battery 및 블레이드 진단
- 하부 가드 및 브레이크 점검
- 소유자 안전 경계
This preview shows only a portion of the complete repair manual. Purchase to access the full repair documentation, downloadable PDF and detailed repair procedures.
예상 근본 원인
- Battery pack is discharged, too hot or cold, or faulty
- Pack is not fully seated or its contacts are obstructed
- Trigger lock-off button is not fully released or is damaged
- Trigger movement is blocked or damaged
- Internal switch, controller, or motor fault
- Rails contain packed dry debris or are damaged
- Battery case or tool rails are cracked or distorted
- Latch or release button is jammed or broken
- Wrong or incompatible battery pack is being tried
- Battery interface or housing is impact-damaged
- Pack protection opened for charge or temperature
- Blade was pinched, bound, or overloaded by the cut
- Pack is loose or the contacts are intermittent under vibration
- Blocked vents or heavy loading caused thermal protection
- Internal control or motor fault
- Battery charge or output is too low for the load
- Blade is dull, dirty, damaged, or unsuitable
- Blade rotation, size, arbor, or speed rating is incorrect
- Cut depth is excessive or feed pressure is too high
- Motor, bearing, or electronic drive fault
- Dry debris obstructs the trigger or lock-off button
- Trigger or lock-off is cracked or impact-damaged
- Trigger return or lock-off spring mechanism has failed
- Liquid or contamination entered the control area
- Internal switch or electronic control fault
- Battery is nearly depleted or protection is unstable
- Trigger does not return fully to the off position
- Blade or spindle has excessive drag, looseness, or damage
- Electronic brake or controller has failed
- Motor or internal wiring fault
- Sawdust or chips obstruct the guard path
- Guard is bent, cracked, or misassembled
- Retracting lever, pivot, or spring is damaged
- Blade or clamp parts rub the guard at some angles or depths
- Guard mechanism requires qualified adjustment or replacement
- Blade lock is not aligned with the spindle
- Wrong direction used on the right-hand screw
- Sawdust packed around clamp washer or spindle
- Spindle lock or threads are damaged internally
- Blade is mounted in the wrong rotation direction
- Blade size or 5/8 inch arbor hole is incorrect
- Outer washer is reversed or the screw is loose
- Blade is bent, cracked, dirty, or below the required speed rating
- Spindle, clamp washer, bearing, or shoe is damaged
- Depth lever is not fully loosened or tightened
- Sawdust is packed in the shoe slide or pivot
- Depth scale, lever, pivot, or shoe is bent or damaged
- Fastener or clamping surface is worn or loose
- Internal or structural adjustment repair is required
- Battery charge is too low for a valid test
- Trigger is not moving far enough to activate the light
- Lens area is blocked by dry debris
- LED or wiring is damaged
- Switch or electronic control fault
- Workpiece support lets the kerf close on the blade
- Blade is dull, damaged, dirty, or installed incorrectly
- Depth or bevel lever is loose or set incorrectly
- Saw is twisted, forced, or restarted in the kerf
- Fastener, knot, or offcut pinches the blade
- Bevel lever is not fully tightened
- Sawdust blocks the quadrant or shoe pivot
- Pointer or calibration stop is out of adjustment
- Shoe, quadrant, or pivot is bent from impact
- Blade or spindle runout is creating a false angle
- Vents are blocked by sawdust or the saw is covered
- Blade is dull or the feed load is excessive
- Battery is hot, cold, low, damaged, or unsuitable
- Cut depth, support, or material is overloading the saw
- Motor, bearing, controller, or battery fault
- Blade is bent, cracked, loose, dirty, or mounted off-center
- Guard or shoe is rubbing the blade
- Sawdust or a foreign object is caught near the blade or guard
- Spindle, bearing, gearcase, or motor is damaged
- Housing, handle, shoe, or fastener is loose or cracked
- Battery is swollen, leaking, cracked, or venting
- Liquid entered the battery, switch, motor, or housing
- Internal electrical short or overheating component
- Guard, shoe, handle, or housing exposes parts
- Impact or fire damage makes the saw unsafe
지원 모델
관련 모델
일반적인 증상
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
고장 모드
요약
- 잠금 해제 버튼과 트리거를 눌러도 motor 또는 블레이드가 움직이지 않음 - 작업등이 꺼져 있을 수 있음.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
요약
battery가 정상적으로 슬라이드되지 않거나 걸리지 않거나 유지되지 않거나 해제되지 않습니다.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
요약
톱이 시작되었다가 트리거를 누른 상태에서 부하 또는 무부하 상태에서 멈춥니다.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
요약
블레이드는 회전하지만, 올바르게 지지된 목재 절단에서 속도 또는 절단력이 정상 이하입니다.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
요약
잠금 해제가 트리거를 차단하거나 해제하지 못하거나 트리거가 끼이거나 신뢰할 수 없게 작동합니다.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
요약
트리거 해제 후 블레이드가 너무 오래 관성으로 돌거나 멈춤이 일관되지 않습니다.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
요약
하부 가드가 걸리거나 느리게 움직이거나 마찰이 있거나 열려 있거나 블레이드를 덮지 못합니다.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
요약
블레이드 잠금이 작동하지 않거나 클램핑 screw가 풀리거나 조여지지 않거나 블레이드와 와셔를 안전하게 조립할 수 없습니다.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
요약
블레이드가 이동하거나 중심을 벗어나거나 가드에 마찰을 일으키거나 이가 가드 화살표와 반대 방향입니다.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
요약
슈가 깊이에서 설정되거나 고정되지 않거나 사용 중 절단 깊이가 변합니다.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
요약
작업등이 어둡거나 깜박이거나 트리거 해제 후 지연이 비정상적입니다.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
요약
블레이드가 끼이거나 커프에서 멈추거나 톱이 올라가거나 안전하게 다시 시작할 수 없습니다.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
요약
경사 레버가 잠기지 않거나 쿼드런트 설정이 움직이거나 포인터가 0일 때 절단이 직각이 아닙니다.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
요약
톱 또는 팩이 비정상적으로 뜨거워지거나 출력이 떨어지거나 지지된 절단 중에 멈춥니다.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
요약
톱이 작업물로 인한 것이 아닌 거친 소음이나 진동을 발생시킵니다.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
요약
연기, 불꽃, 타는 냄새, 액체, battery 손상, 위험한 열 또는 노출된 구조가 있습니다.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
관련 매뉴얼
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기
세부 정보 보기