Search repair guides
Find repair guides, manuals, symptoms, and error codes across the knowledge base.
A wet or damp pad is installed, but the robot produces no spray and leaves the floor dry.
The tank is filled to the top and installed flat, but the red sweep or Error 37 still says to fill it.
The correct wet or damp cycle leaves pooling or substantially more water than expected.
The pass count or spray behavior does not match the installed wet, damp, or dry pad.
The 200-series robot is awake nearby, but the iRobot app cannot add or connect to it.
The robot is charged but cannot drive off the Home Base when a job begins after clearance and placement are proven.
The robot drives and sprays, but the cleaning head lacks its normal scrubbing vibration with a wet pad.
The robot runs normally but the charged battery lasts far less than a typical job.
The robot wakes but the battery level does not rise on the Home Base, or the app announces a charging error.
The charged robot can show some activity, but CLEAN presses, indicators, or tones are missing, delayed, or inconsistent.
The robot charges fully, but ends early with low battery, repeatedly recharges, or cannot reach the Home Base before Error 46.
The robot moves, but one wheel makes repeatable noise or feels rough through rotation.
The two blue-line mode activates, but the robot travels beyond the intended invisible boundary.
The jet pulses irregularly, sprays off-pattern, or carries visible contaminated water.
The robot powers down before the job is complete and gives no repeatable beep count.
The pad no longer lies flat and interferes with smooth travel.
The chassis moves beyond a true floor edge instead of backing away.
The job ends with a docking problem or the robot cannot find the Home Base after placement, clearance, and map-start checks are corrected.
The charger light remains dark with the charger connected to a known live outlet.
The pad card stops short, binds, or will not remain seated in both underside rails.
FM-19: NO WATER SPRAYS OR THE FLOOR STAYS DRY
FM-27: THE PAD HEAD DOES NOT VIBRATE IN WET MOPPING MODE
FM-15: THE PRECISION JET SPRAY IS WEAK, DELAYED, OR ABSENT
FM-23: THE FLOOR IS LEFT TOO WET
FM-26: THE ROBOT CHOOSES THE WRONG MOTION OR WETNESS FOR THE PAD
FM-01: THE ROBOT WILL NOT TURN ON OR WAKE
FM-01: THE ROBOT DOES NOT POWER ON
FM-20: THE PRECISION JET SPRAY IS TOO WEAK
FM-02: THE ROBOT WILL NOT CHARGE OR SHOWS A CHARGING ERROR
FM-25: THE PAD EJECT SLIDER WILL NOT RELEASE THE PAD
FM-03: THE BATTERY NEVER REACHES A FULL CHARGE
FM-13: THE CLEANING PAD WILL NOT SLIDE IN OR EJECT
FM-32: THE CLEAN BUTTON, LIGHTS, OR TONES RESPOND ABNORMALLY
FM-17: THE ROBOT CROSSES A REAL DROP OR FAILS TO STOP AT STAIRS
FM-16: THE ROBOT MISSES AREAS OR ENDS BEFORE EXPECTED COVERAGE
FM-09: THE ROBOT WILL NOT UNDOCK
FM-05: THE ROBOT SHUTS OFF MID-CYCLE WITHOUT A DISTRESS CODE
FM-21: THE SPRAY SPUTTERS, IS UNEVEN, OR CONTAINS RESIDUE
FM-33: THE HOUSING, HANDLE, TANK, OR NOZZLE IS CRACKED
FM-28: THE PAD DRAGS, BUNCHES, SEPARATES, OR RUBS A WHEEL
Pad tracks and attachment card
Pad-detection sensor
Dry cloth
Dry microfiber cloth
Dry towels
FM-19
FM-27
Fresh compatible wet pad
Top handle and pad eject control
Clean lightly dampened melamine foam or cloth
Compatible battery, no hazard
Control board and wiring
Fresh compatible pad
Front and rear cliff sensors
Genuine tank or cap item
Left and right drive wheels
Precision Jet Spray nozzle
Pump, motors, and gearbox
Rear battery bay and latch
Tank cap and 150 mL reservoir
