搜索维修指南
在知识库中查找维修指南、手册、症状和错误代码。
Serra desliga sob carga
The saw starts normally but stops, pulses, or loses power during a cut, especially when pushed or when the battery is moved.
The saw suddenly lifts, jumps toward the operator, climbs out of the kerf, or walks backward as the blade pinches or twists.
主轴锁无法啮合，附带扳手无法转动bolt，或刀片bolt卡死、滑丝或错牙。
能听到motor运转声，但刀片静止、启动迟缓或打滑，未跟随motor转动。
Motor 运行但锯片不转
La hoja vibra o rechina
La hoja funciona descentrada, toca el protector o la zapata, produce vibración inusual o hace un ruido de molienda.
锯完成切割，但0度切割不方正，斜切角度与刻度不符，或锯缝偏离预定角度。
鞋无法旋转或滑动，深度杆或斜切旋钮无法锁定，或操作或切割时设定发生偏移。
The blade turns, but the saw feeds poorly, stalls in the kerf, burns the wood, splinters excessively, or overloads during an ordinary cut.
插入battery时刀片启动，扳机卡住，或释放扳机无法断电。
360度除尘口卡住或松动，或兼容的软管/接头无法保持连接。
The external structure is visibly cracked, loose, crushed, melted, or missing material even if the saw still runs.
锯子启动后负载下突然关闭
The bar is bent or cracked, chain links or cutters are broken, or the guide-bar scabbard is split, missing, or will not stay on.
The reservoir contains oil but the chain stays dry, the primer gives no visible result, or the bar oil path remains dry.
WORKLIGHT COMES ON, BUT THE MOTOR WILL NOT START
Spoušť se plně nevrací ven, nebo motor/kotouč běží i po uvolnění spouště.
The quick-release collar binds, will not move fully forward, or stays forward after release.
FM-07: 刀片晃动、摩擦、振动或磨损
FM-05: 锯在负载下关闭或断续切割
FM-08: 切割缓慢、卡顿、停转、烧焦或碎裂
FM-04: 插入BATTERY时锯启动或无法停止
FM-09: 锯反冲、爬升或后退
FM-06: MOTOR运转但刀片不转
FM-11: 深度或斜切调节无法移动或固定
FM-12: 刀片BOLT或主轴锁无法操作
FM-10: 切割不方正或斜切角度不准确
FM-11: 空载锯片速度低、波动或断断续续，未接触木材前
FM-03: The Saw Starts, Then Cuts Out With The Trigger Held
FM-05: FM-05 SPEED WILL NOT VARY, SURGES, OR CUTS ERRATICALLY
FM-15: FM-15 BATTERY 存储断开连接时快速失电
fm-3-2: CHARGE-STATUS INDICATOR GIVES NO RESPONSE AFTER A CONFIRMED FULL CHARGE
FM-05: 如果锯子在确认有电且控制自由的情况下仍无反应，保持机壳关闭，
FM-21: FM-21 导轨、锯链、护套或切割附件损坏
FM-27: FM-27 工具或电池组过热，或热关闭重复发生
FM-08: FM-08 链条松弛、下垂或无法保持张力
FM-12: FM-12 链条移动但因安装反向而不切割
FM-15: FM-15 链条使用中跳脱或脱轨