CMCS500M1

型号： CMCS500M1

亦称： CMCS500, CRAFTSMAN V20 Circular Saw, CMCS500M1

• Craftsman Cmcs500m1 Repair Manual

• The blade turns, but the saw feeds poorly, stalls in the kerf, burns the wood, splinters excessively, or overloads during an ordinary cut.

  The blade turns, but the saw feeds poorly, stalls in the kerf, burns the wood, Release the trigger, hold the saw still until the blade stops, remove it from the cut only after FM-08

• 主轴锁无法啮合，附带扳手无法转动bolt，或刀片bolt卡死、滑丝或错牙。

  主轴锁无法啮合，附带扳手无法 1. 拆下battery，使用附带的内六角扳手，按下主轴锁，同时

• The saw suddenly lifts, jumps toward the operator, climbs out of the kerf, or walks backward as the blade pinches or twists.

  The saw suddenly lifts, jumps toward the operator, climbs out of the kerf, or Release the trigger and hold the saw motionless in the material until the blade completely FM-09

• 鞋无法旋转或滑动，深度杆或斜切旋钮无法锁定，或操作或切割时设定发生偏移。

  底板无法旋转或滑动，深度杆或斜角旋钮 1. 拆下battery并支撑底板，然后仅释放正在检查的深度杆或斜角旋钮。

• Saw cuts out under load

  Saw cuts out under load Electronic protection, weak pack, intermittent contact, overload, or internal fault; use FM-05.

• Motor 运行但锯片不转

  Motor 运行但锯片不转 锯片夹紧、齿轮或主轴驱动故障；使用 FM-06。

• 锯完成切割，但0度切割不方正，斜切角度与刻度不符，或锯缝偏离预定角度。

  锯完成切割，但0度切割不方正， 1. 拆下battery，将斜角设为零，在底板和刀片本体之间放置方尺，避开硬质合金齿。

• The blade runs off-center, touches the guard or shoe, produces unusual vibration, or makes a grinding sound.

  The blade runs off-center, touches the guard or shoe, produces 1. Remove the battery, place the saw on a stable surface, and inspect the blade for

• 能听到motor运转声，但刀片静止、启动迟缓或打滑，未跟随motor转动。

  可以听到motor运行声，但刀片保持静止，

• The saw starts normally but stops, pulses, or loses power during a cut, especially when pushed or when the battery is moved.

  The saw starts normally but stops, pulses, or loses power 1. Release the trigger, hold the saw still until the blade stops, remove the battery, and let

• 插入battery时刀片启动，扳机卡住，或释放扳机无法断电。

  刀片在插入battery时启动，扳机卡住，或释放扳机未使锯子断电。1. 保持刀片清洁，释放扳机，且在安全时立即移除battery；切勿将带动刀片的锯子放下。

• Blade wobbles or grinds

  Blade wobbles or grinds Blade setup, damage, shoe or guard contact, spindle, or bearing fault; use FM-07.

• FM-09: 锯反冲、爬升或后退

  锯出现反冲行为：突然抬起、向操作者跳跃、从锯缝爬出或因刀片夹紧或扭曲而后退。

• FM-11: 深度或斜切调节无法移动或固定

  深度或斜切调节机构无法移动、锁定或保持设定，导致切割不准确且操作不安全。

• FM-05: 锯在负载下关闭或断续切割

  FM-05 锯在负载下关闭或断续切割

• FM-06: MOTOR运转但刀片不转

  FM-06 MOTOR运转但刀片不转

• FM-07: 刀片晃动、摩擦、振动或磨损

  FM-07 刀片摆动、摩擦、振动或研磨

• FM-08: 切割缓慢、卡顿、停转、烧焦或碎裂

  切割性能问题，刀片转动但锯送料不畅、卡顿、烧焦木材或切割时碎裂严重。建议立即停止使用以防损坏或伤害。

• FM-12: 刀片BOLT或主轴锁无法操作

  FM-12 刀片BOLT或主轴锁无法操作

• FM-04: 插入BATTERY时锯启动或无法停止

  插入battery时锯片立即旋转，或松开扳机后锯无法停止运行。这是严重安全隐患，需立即处理。

• FM-10: 切割不方正或斜切角度不准确

  FM-10 切割不方正或斜切角度不准确