CMCS500M1

型号： CMCS500M1

亦称： CMCS500, CRAFTSMAN V20 Circular Saw, CMCS500M1

• Craftsman Cmcs500m1 Repair Manual

• The blade turns, but the saw feeds poorly, stalls in the kerf, burns the wood, splinters excessively, or overloads during an ordinary cut.

  The blade turns, but the saw feeds poorly, stalls in the kerf, burns the wood, Release the trigger, hold the saw still until the blade stops, remove it from the cut only after FM-08

• 主軸鎖無法啟動，附送扳手無法轉動bolt，或鋸片bolt卡死、滑牙或交叉螺紋。

  主軸鎖無法啟動，附帶扳手無法 1. 拆除 battery，使用附帶六角扳手，按壓主軸鎖，同時手動旋轉鋸片直到鎖完全啟動。

• The saw suddenly lifts, jumps toward the operator, climbs out of the kerf, or walks backward as the blade pinches or twists.

  The saw suddenly lifts, jumps toward the operator, climbs out of the kerf, or Release the trigger and hold the saw motionless in the material until the blade completely FM-09

• 鋸鞋無法擺動或滑動，深度桿或斜切旋鈕無法鎖定，或操作或切割時設定會移位。

  鞋子無法旋轉或滑動，深度桿或斜角旋鈕 1. 拆除 battery 並支撐鞋子，然後僅鬆開正在檢查的深度桿或斜角旋鈕。

• Saw cuts out under load

  Saw cuts out under load Electronic protection, weak pack, intermittent contact, overload, or internal fault; use FM-05.

• Motor 運轉但鋸片冇轉

  Motor 運轉但鋸片冇轉 鋸片夾、齒輪或主軸驅動故障；用 FM-06。

• 鋸完成切割，但0度切割不方正，斜切角度與刻度不符，或切口偏離預期角度。

  鋸子完成切割，但 0 度切割不方正， 1. 拆除 battery，將斜角設為零，並將方尺放在鞋子和鋸片本體之間，避開硬質合金齒。

• The blade runs off-center, touches the guard or shoe, produces unusual vibration, or makes a grinding sound.

  The blade runs off-center, touches the guard or shoe, produces 1. Remove the battery, place the saw on a stable surface, and inspect the blade for

• 可以聽到motor運轉，但鋸片保持靜止、啟動遲或打滑，無法跟隨motor轉動。

  可以聽到motor運行聲，但刀片保持靜止， 1. 放開扳機，等所有動作停，拆除battery，唔好再用鋸機直到檢查刀片驅動。

• The saw starts normally but stops, pulses, or loses power during a cut, especially when pushed or when the battery is moved.

  The saw starts normally but stops, pulses, or loses power 1. Release the trigger, hold the saw still until the blade stops, remove the battery, and let

• 插入battery時鋸片啟動，扳機卡住，或鬆開扳機無法斷電。

  刀片喺插入battery時啟動，扳機卡住，或者放開扳機冇令鋸機斷電。1. 保持刀片清潔，放開扳機，安全時即刻拆除battery；唔好放低有刀片轉動嘅鋸機。

• Blade wobbles or grinds

  Blade wobbles or grinds Blade setup, damage, shoe or guard contact, spindle, or bearing fault; use FM-07.

• FM-09: 鋸反彈、爬升或向後走

  鋸出現反彈行為：突然抬起、向操作者跳動、從切口爬出或因鋸片夾緊或扭曲而向後走。

• FM-11: 深度或斜切調校無法移動或固定

  深度或斜切調校機構無法移動、鎖定或保持設定，導致切割不準確同操作不安全。

• FM-05: 鋸在負載下關閉或斷斷續續切割

  FM-05 鋸在負載下關閉或斷斷續續切割

• FM-06: MOTOR運轉但鋸片不轉

  FM-06 MOTOR運轉但鋸片不轉

• FM-07: 鋸片搖晃、摩擦、震動或磨損

  FM-07 鋸片震動、摩擦、震盪或磨損

• FM-08: 切割慢、卡住、停轉、燒焦或碎裂

  切割性能問題，鋸片轉動但鋸進差、卡住、燒焦木材或過度碎裂。建議立即停止使用以防損壞或受傷。

• FM-12: 鋸片BOLT或主軸鎖無法操作

  FM-12 鋸片BOLT或主軸鎖無法操作

• FM-04: 插入BATTERY時鋸啟動或無法停止

  插入battery時鋸片即刻轉動，或鬆開扳機後鋸無法停止。呢個係嚴重安全隱患，需即時處理。

• FM-10: 切割不方正或斜切角度不準確

  FM-10 切割不方正或斜切角度不準確