搜索维修指南
在知识库中查找维修指南、手册、症状和错误代码。
360度除尘口卡住或松动，或兼容的软管/接头无法保持连接。
The external structure is visibly cracked, loose, crushed, melted, or missing material even if the saw still runs.
The trigger returns normally and power drops, but the anvil repeatedly coasts instead of stopping promptly.
The direction lever will not reach forward, reverse, or center lock, or the selected position does not hold.
The motor can be heard, but the front output remains still in both directions with the bit removed.
Den löpande sågen hoppar, vibrerar mot arbetsstycket, fastnar eller sparkar bakåt eller åt sidan.
THE BATTERY WILL NOT SEAT, LATCH, RELEASE, OR STAY SECURE
Spoušť se plně nevrací ven, nebo motor/kotouč běží i po uvolnění spouště.
锯子启动后负载下突然关闭
Bladet lämnar linjen, böjs överdrivet, böjs eller går av under en annars kontrollerad skärning.
Motor runs, chain does not
Chain moves but does not cut
Motosega morta con pacco carico
The reservoir contains oil but the chain stays dry, the primer gives no visible result, or the bar oil path remains dry.
The saw cuts slowly, makes fine dust instead of chips, chatters in the kerf, or must be pushed hard despite judging sharpness.
The bar is bent or cracked, chain links or cutters are broken, or the guide-bar scabbard is split, missing, or will not stay on.
锯子完全无反应 - 无工作灯且无 Motor 响应
Battery 膨胀、泄漏、开裂、潮湿、烧焦或异常发热
链条绕导板移动但仅摩擦木材，几乎不产生木屑，无法进入切口。
Klemmen vil ikke bevege seg
FM-31: FM-31 底座弯曲、开裂、松动或无法平放
FM-30: FM-30 锯在斜切设为零度时切割不方正
FM-13: 锯或齿轮箱异常发热或有热味但无烟无火花
FM-05: 锯在负载下关闭或断续切割
FM-03: The Saw Starts, Then Cuts Out With The Trigger Held
FM-02: FM-02 电池无法充电或充电器无法就绪
fm-p16-b-16f80f31: Sätt tillbaka en hel kedja på drivhjulet och i hela ledarfåran, montera ihop,
fm-p14-b-93c34c19: 边界：如果张紧控制无法转动或夹紧，
FM-05: 如果锯子在确认有电且控制自由的情况下仍无反应，保持机壳关闭，
FM-11: 空载锯片速度低、波动或断断续续，未接触木材前
FM-14: FM-14 空载行程磨擦、敲击、卡滞或振动
FM-18: FM-18 油从盖子、油箱或机壳泄漏
FM-21: FM-21 导轨、锯链、护套或切割附件损坏
FM-22: FM-22 BATTERY 或充电器过热、膨胀、开裂、泄漏或冒烟
FM-20: FM-20 异常磨损、响声或剧烈振动
FM-14: FM-14 锯切歪斜或向一侧偏移
FM-16: FM-16 手动引油器不向导板和链条供油
FM-06: FM-06 触发器或锁止开关卡滞、间歇性工作或无法停止锯子
FM-10: Motor 停止但电刹车不再减少锯片惯性旋转
FM-08: FM-08 安装的刀片无法释放