Manual Perbaikan Craftsman CMCD700C1
Manual perbaikan tingkat pemilik untuk kit bor/pengemudi tanpa kabel Craftsman CMCD700C1 V20, merinci 32 mode kegagalan dengan diagnostik, perbaikan, dan info suku cadang untuk menghemat biaya penggantian.
$39.99
Last updated Aug 8, 2026, 5:49 AM
Manual information
About this manual
Manual perbaikan tingkat pemilik untuk kit bor/pengemudi tanpa kabel Craftsman CMCD700C1 V20, merinci 32 mode kegagalan dengan diagnostik, perbaikan, dan info suku cadang untuk menghemat biaya penggantian.
0% Reported Successful Repair
Get the Full Repair Manual — save US$60–US$90
$39.99
Full Manual Includes
- root cause analysis
- tools needed
- step-by-step repair procedure
- diagrams
- exploded views
- post-repair checks
Table of contents preview
- Perbaiki sebelum mengganti hemat $60 - $90
- Kit Bor/driver Tanpa Kabel V20 1/2 In - 32 Mode Kerusakan Berbeda
- V20 Battery + Charger Disetujui Terpisah
- Motor yang Disikat + Rem Listrik + Gearbox 2-kecepatan
- Enam Hal yang Paling Penting
- Apa yang Sebenarnya Dimiliki Model Ini
- Batas Keselamatan.
- Peta Indikator dan Sinyal
- Peringatan Revisi Model
- Jalur Daya
- Urutan Penggunaan Normal
- Perilaku Normal yang Bisa Terlihat Seperti Kesalahan
- Apa yang Tidak Dimiliki Model Ini
- Tekanan Pemicu
- Atau Kerja Intermiten
This preview shows only a portion of the complete repair manual. Purchase to access the full repair documentation, downloadable PDF and detailed repair procedures.
Likely Root Causes
- Battery is discharged, temperature-protected, or internally failed
- Battery contacts are dirty or the pack is not fully seated on the rails
- Forward/reverse button is centered or not fully in a drive detent
- Trigger, contact block, wiring, brushes, motor, or switch has failed
- Debris or a raised edge blocks a rail or contact channel
- Battery is misaligned or is not a compatible V20 interface
- Battery shell or tool rail support is swollen, cracked, or distorted
- Release latch or contact block is damaged and out of position
- Battery is not fully seated in the charger
- Outlet or charger has no power or blocked ventilation
- Battery is outside the permitted temperature range
- Battery or charger has internally failed
- Dry contamination, wear, or damage at the battery contacts
- Battery shell or latches allow electrical movement despite physical retention
- Tool contact block or internal wiring is loose
- Trigger, direction switch, brush, or motor connection is intermittent
- Selector is not pushed fully to the intended side
- External cap moves but does not actuate the internal switch
- Direction-switch contacts are worn or burned
- Wiring, trigger, brush, or motor connection fails in one polarity path
- Selector is not fully centered
- External selector or trigger interlock is worn or broken
- Housing damage misaligns the control parts
- Internal direction switch or lock feature has failed
- Gear teeth are temporarily misaligned
- Debris or housing damage blocks selector travel
- External selector cap or fork is damaged
- Internal shift fork or gearbox component is jammed
- Debris or impact damage blocks the collar
- Collar shell or detent ring is cracked or displaced
- Internal clutch spring or adjustment mechanism is jammed
- Housing or gearbox alignment is damaged
- Collar is actually in drill mode or a high setting
- Fastener, bit, or scrap material is unsuitable for the comparison
- Clutch cam, spring, or detent is jammed
- Gearbox or spindle bypasses the torque-limiting mechanism
- Numbered setting is too low for the fastener
- Collar is between detents or drill mode is not fully aligned
- Bit, fastener, or material is causing abnormal resistance
- Clutch spring, cam, gear, or drive interface is worn or broken
- Dust, chips, corrosion, or a damaged bit binds the jaws
- The bit is side-loaded or bottomed incorrectly
- Chuck sleeve, jaw scroll, or automatic spindle lock is damaged
- Impact or overtightening distorted the chuck
- Bit was not inserted straight or enough jaw length was not engaged
- Chuck was not tightened firmly by hand
- Bit shank is oily, undersized, worn, or damaged
- Chuck jaws or internal scroll are worn despite normal movement
- Spindle has not reached the lock position
- Gear train is between teeth and needs slight hand rotation
- Spindle-lock or gearbox component is worn or broken
- Chuck body is loose on the spindle
- Bit is bent or its shank is damaged
- Bit is gripped off-center by uneven or dirty jaws
- Chuck body is loose, damaged, or internally worn
- Spindle, bearing, gearbox output, or front housing is bent or loose
- Speed selector or shift fork is between engagements
- Gear teeth, keys, shaft, or coupling are stripped or broken
- Clutch drive has failed internally
- Chuck is loose on the spindle or spindle connection has failed
- Debris or damage is present in the chuck or front housing
- Chuck, spindle, bearing, gear, or clutch component is worn or loose
- Brush or motor component is contacting abnormally
- Housing damage has shifted internal alignment
- Bit is dull, wrong for the material, or mismatched to the fastener
- Speed range or clutch setting is wrong for the task
- Work is unsupported, pressure is misdirected, or chips are not clearing
- Battery has reduced capacity under work load
- Internal torque output is reduced without obvious no-load loss
Supported model
Related Categories
Related Models
CRAFTSMAN
View details
CRAFTSMAN
View details
CRAFTSMAN
View details
CRAFTSMAN
View details
CRAFTSMAN
View details
CRAFTSMAN
View details
CRAFTSMAN
View details
CRAFTSMAN
View details
CRAFTSMAN
View details
CRAFTSMAN
View details
CRAFTSMAN
View details
CRAFTSMAN
View details
Common Symptoms
View details
View details
View details
View details
View details
View details
View details
View details
View details
View details
View details
View details
View details
View details
View details
View details
View details
View details
Failure Modes
Summary
Bor/driver tidak mulai meskipun battery V20 yang terverifikasi dan terisi penuh terpasang dan tombol arah sepenuhnya maju atau mundur. Tidak ada suara motor, aktivitas LED, atau gerakan chuck, dan alat tetap tidak responsif.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Summary
inspeksi.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Summary
Paket battery V20 tidak mulai mengisi daya atau gagal menyelesaikan pengisian saat ditempatkan di charger yang disetujui pada suhu ruangan. Charger mungkin tidak menunjukkan indikasi atau tetap dalam status pengisian tanpa batas waktu.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Summary
pemutusan daya tergantung gerakan.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Summary
Pemilih arah alat bergerak normal dan menahan detent, tetapi chuck hanya berputar dalam satu arah atau berputar berlawanan dengan arah yang dipilih.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Summary
FM-16
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Summary
CRAFTSMAN CMCD700C1 V20 KIT BOR/PENGEMUDI 1/2 IN - MOTOR BRUSHED - 2-KECEPATAN - CHUCK TANPA KUNCI - LED
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Summary
FM-19
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Summary
FM-20
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Summary
FM-22
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Summary
FM-23
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Summary
FM-24
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Summary
Chuck atau bit menunjukkan goyangan sisi-ke-sisi yang terlihat atau getaran pada kecepatan rendah tanpa beban setelah bit dipusatkan dan dikencangkan dengan benar.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Summary
Motor Berjalan Tetapi Chuck Tidak Berputar atau Kehilangan Lepaskan pemicu, lepaskan battery, dan hentikan penggunaan jalur penggerak sampai FM-26
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Summary
FM-27
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Summary
FM-28
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Related Manuals
View details
View details
View details
View details
View details
View details
View details
View details
View details
View details
View details
View details