CMCD700C1

型号： CMCD700C1

亦称： CMCD700, V20 Drill/Driver, CMCD700C1

• Craftsman Cmcd700c1 Repair Manual

• 一個正常嘅V20 battery完全就位，方向掣完全前推或後推，工具冇motor聲、LED反應或夾頭動作。死機狀態喺工具靜止時持續。

  一個正常嘅V20 battery完全插好，方向掣完全 1. 將方向掣置中，移除battery，並檢查工具同電池包有冇液體、膨脹、裂紋、熔化或燒焦。

• A compatible V20 battery starts onto the tool rails but binds before reaching the normal seated and latched position.

  A compatible V20 battery starts onto the tool rails but binds 1. Stop pushing and withdraw the binding battery straight off the rails without

• The collar moves normally, but the clutch ratchets before a suitable fastener reaches normal depth at appropriate settings, or it audibly slips when drill mode is correctly selected.

  The collar moves normally, but the clutch ratchets before a 1. Release the trigger at early ratcheting, remove the battery, and verify the collar is

• With the battery removed, the keyless chuck sleeve or jaws remain seized, or a clamped bit cannot be released by normal hand rotation.

  With the battery removed, the keyless chuck sleeve or jaws 1. Center the direction button, remove the battery, support the tool, and support any

• The drill sounds and rotates normally with no load, does not stall, overheat, slip, or vibrate abnormally, yet a corrected drilling or fastening task progresses much more slowly than expected.

  The drill sounds and rotates normally with no load, does not 1. Remove the battery and inspect or replace the bit before changing any tool

• 夾頭停止且移除battery後，頂部選擇器無法完全移入範圍1或範圍2，即使手動轉動夾頭對齊齒輪。

  喺卡盤停咗同拆除battery嘅情況下，頂部選擇器 1. 完全停低卡盤，拆除battery先至觸摸速度選擇器。

• With the battery removed, the clutch collar is physically stuck, cracked, excessively loose, or unable to align a numbered setting or drill mode with the index mark.

  With the battery removed, the clutch collar is physically stuck, 1. Remove the battery before turning or inspecting the mode/torque collar.

• 室溫嘅V20 battery完全就位喺有電嘅認可充電器，但正常充電唔開始或電池包永遠唔顯示充滿。

  室溫嘅V20 battery完全插入有電嘅 1. 從充電器移除battery，檢查電池包、充電器、電線同接觸點有冇液體、膨脹、裂紋、熔化、燒焦或撞擊損壞。

• The chuck jaws open and close normally, but a straight compatible bit rotates or pulls out during moderate drilling or driving.

  The chuck jaws open and close normally, but a straight 1. Release the trigger, remove the battery, and remove or catch the loose bit before

• The collar moves and holds a low numbered setting, but the clutch does not ratchet before a test fastener is overdriven in suitable scrap material.

  The collar moves and holds a low numbered setting, but the 1. Remove the battery and set up a matching fastener and sound driver bit in

• The chuck still rotates, but a new mechanical grind, knock, scrape, tight spot, or severe vibration remains with the bit removed and is not ordinary motor or brake sound.

  The chuck still rotates, but a new mechanical grind, knock, 1. Stop at the first new mechanical noise or severe vibration, remove the battery, and

• 電鑽/起子喺驗證過嘅 BATTERY 下唔會啟動

  FM-01 電鑽/起子喺驗證過嘅 FM-09 BATTERY 運行時間遠短於預期

• FM-01: 電鑽/起子喺驗證過嘅 BATTERY 下唔會啟動

  即使裝咗驗證過、充滿電嘅 V20 battery，電鑽/起子都唔會啟動，方向按鈕完全前或後。冇 motor 聲音、LED 活動或夾頭動作，工具無反應。

• FM-17: 兩速選擇器唔會喺檔位間移動

  Craftsman CMCD700C1 V20 1/2吋電鑽/起子套裝 - 有刷MOTOR - 兩速 - 無匙夾頭 - LED燈

• FM-27: 工具有新嘅磨擦、敲擊、卡住或者嚴重震動

  FM-27

• FM-28: 鑽孔或緊固慢，儘管無負載運轉正常

  FM-28

• FM-23: 鑽頭喺夾頭滑動或拉出

  FM-23

• FM-20: 離合器永遠唔鬆開，喺低設定下過度驅動緊固件

  FM-20

• FM-25: 夾頭或鑽頭喺無負載時明顯擺動

  夾頭或鑽頭喺低速無負載時有明顯嘅側向擺動或偏擺，鑽頭已正確居中同緊固。

• FM-15: 工具只喺一個方向運轉或反方向運轉

  工具嘅方向選擇器正常移動並保持卡位，但夾頭只喺一個方向運轉或反方向旋轉。

• FM-22: 夾頭唔可以用手打開或者關閉，或者鑽頭鬆唔開

  夾頭唔可以用手打開或者關閉，或者鑽頭鬆唔開

• FM-16: 中央鎖唔阻擋扳機

  FM-16

• FM-21: 離合器過早鬆開或喺鑽孔模式打滑

  FM-22

• FM-06: 工具或BATTERY移動時斷電

  依賴移動嘅斷電現象。