BLACK+DECKER LCS1020 Repair Manual

Comprehensive repair guide for the BLACK+DECKER LCS1020 cordless chainsaw, including troubleshooting, maintenance, and repair instructions for 24 common faults.

$39.99

Laatst bijgewerkt Aug 1, 2026, 1:13 AM

Over deze handleiding

Comprehensive repair guide for the BLACK+DECKER LCS1020 cordless chainsaw, including troubleshooting, maintenance, and repair instructions for 24 common faults.

0% Reported Successful Repair

Price

$39.99

Volledige handleiding bevat

root cause analysis
tools needed
step-by-step repair procedure
diagrams
exploded views
post-repair checks

Inhoudsopgave voorvertoning

Black+decker Lcs1020
The Six Things That Matter Most
What This Model Actually Has
Indicator And Signal Map
Model-revision Warning
The Cutting Path
Normal Use Sequence
Normal Behavior That Can Look Like A Fault
What This Model Does Not Have
The Saw
Unusable
FM-08 CHAIN IS LOOSE, SAGS, OR WILL NOT HOLD TENSION
FM-20 ABNORMAL GRINDING, RATTLING, OR SEVERE VIBRATION
FM-09 CHAIN IS TOO TIGHT, BINDS BY HAND, OR BAR AND CHAIN OVERHEAT
FM-21 GUIDE BAR, SAW CHAIN, SCABBARD, OR CUTTING ATTACHMENT IS

This preview shows only a portion of the complete repair manual. Purchase to access the full repair documentation, downloadable PDF and detailed repair procedures.

Ondersteund model

Bekijk probleemoplossingspagina van model

BLACK+DECKER

Bdcr20c

Details bekijken

BLACK+DECKER

Bdcdd12c

Details bekijken

BLACK+DECKER

Ld120va

Details bekijken

BLACK+DECKER

Bdci20c

Details bekijken

The battery will not slide fully into the tool, click into place, stay latched, or release normally.

Details bekijken

The chain travels around the bar but only rubs the wood, produces almost no chips, and will not enter the cut.

Details bekijken

The saw chain leaves the guide-bar groove, hangs from the bar, or comes off the drive sprocket.

Details bekijken

Bar oil forms a fresh puddle, runs from the cap, or appears from the body while the saw is idle or stored.

Details bekijken

The cap will not close, the primer is split or stuck, or the oil-level indicator is cracked, clouded, or leaking.

Details bekijken

The saw cuts slowly, makes fine dust instead of chips, chatters in the kerf, or must be pushed hard despite judging sharpness.

Details bekijken

The lock-off or trigger will not move freely, does not return, responds intermittently, or the motor continues after the trigger is released.

Details bekijken

The reservoir contains oil but the chain stays dry, the primer gives no visible result, or the bar oil path remains dry.

Details bekijken

Saw dead with charged pack

Details bekijken

The saw makes new grinding, clacking, rattling, or strong vibration during no-load running or cutting.

Details bekijken

After chain or bar work, the cover will not sit flush, the bar will not align, or the locking knob cannot begin correctly.

Details bekijken

The bar is bent or cracked, chain links or cutters are broken, or the guide-bar scabbard is split, missing, or will not stay on.

Details bekijken

Motor runs, chain does not

Details bekijken

The guide bar steers sideways in the cut or the kerf curves even though the workpiece is supported and the saw is held square.

Details bekijken

Chain moves but does not cut

Details bekijken

The guide bar cannot be withdrawn from the kerf, the chain is trapped, or the workpiece closes on the saw.

Details bekijken

The lithium battery or charger shows abnormal heat, swelling, cracking, electrolyte, hissing, odor, sparks, or smoke.

Details bekijken

The chain hangs below the guide bar, can be pulled too far from the rail, or becomes loose again after adjustment.

Details bekijken

Liquid entered the tool, the housing emits smoke or sparks, plastic melts, a burning odor appears, or wiring or contacts are exposed.

Details bekijken

The chain is hard to pull around the bar, the bar becomes unusually hot, or smoke appears without an electrical odor.

Details bekijken

The front hand guard, front or rear handle, main housing, ribbed bumper, fastener, battery well, or another external part is cracked, loose, or missing.

Details bekijken

A tool-free knob is frozen, cross-threaded, spins without effect, will not clamp the bar, or cannot hold the set tension.

Details bekijken

The motor can be heard, but the chain remains stationary or only twitches while the trigger is held.

Details bekijken

FM-01: FM-01 BATTERY PACK WILL NOT INSERT, LATCH, OR RELEASE

Samenvatting

Battery pack will not insert, latch, or release properly, preventing tool operation.

Full repair guide includes

Root Cause Analysis
Required Tools
Replacement Parts
Step-by-step Repair Procedure
Safety Precautions
Verification Checklist

BLACK+DECKER LCS1020 Repair Manual

Manual information

Over deze handleiding

Volledige handleiding bevat

Inhoudsopgave voorvertoning

Ondersteund model

Gerelateerde modellen

Veelvoorkomende symptomen

Storingsmodi

Gerelateerde handleidingen