LCS1020

Modelnummer: LCS1020

Ook bekend als: BD, Black and Decker, LCS1020

• Black Decker Lcs1020 Repair Manual
• Black Decker Lcs1020 Repair Manual 90347630
• Black Decker Lcs1020 Repair Manual Fb4bc7e8

• Bar oil forms a fresh puddle, runs from the cap, or appears from the body while the saw is idle or stored.

  Bar oil forms a fresh puddle, runs from the cap, or 1. Remove the battery, wipe the saw clean, and place it upright over an absorbent

• Motor runs, chain does not

  Motor runs, chain does not Inspect chain engagement, sprocket, bar groove, and gearbox through FM-11.

• The bar is bent or cracked, chain links or cutters are broken, or the guide-bar scabbard is split, missing, or will not stay on.

  The bar is bent or cracked, chain links or cutters are 1. Remove the battery and do not run the saw with a bent bar, cracked rail, broken link,

• The saw cuts slowly, makes fine dust instead of chips, chatters in the kerf, or must be pushed hard despite judging sharpness.

  The saw cuts slowly, makes fine dust instead of chips, 1. Remove the battery and verify chain direction, cooled tension, and lubrication before

• The reservoir contains oil but the chain stays dry, the primer gives no visible result, or the bar oil path remains dry.

  The reservoir contains oil but the chain stays dry, the 1. Remove the battery, place the saw level, and fill with approved bar-and-chain oil if

• A tool-free knob is frozen, cross-threaded, spins without effect, will not clamp the bar, or cannot hold the set tension.

  effect, will not clamp the bar, or cannot hold the set tension. 1. Remove the battery and do not use pliers or excessive force on either plastic knob. and cover clean, and inspect for cracks or stripping.

• The chain is hard to pull around the bar, the bar becomes unusually hot, or smoke appears without an electrical odor.

  The chain is hard to pull around the bar, the bar 1. Release the trigger, remove the battery, and let the bar and chain cool before

• The chain hangs below the guide bar, can be pulled too far from the rail, or becomes loose again after adjustment.

  The chain hangs below the guide bar, can be pulled too 1. Remove the battery, let a hot chain cool, and check for no visible sag under the

• The guide bar cannot be withdrawn from the kerf, the chain is trapped, or the workpiece closes on the saw.

  The guide bar cannot be withdrawn from the kerf, the 1. Release the trigger, remove the battery, wait for all movement to stop, and keep

• The cap will not close, the primer is split or stuck, or the oil-level indicator is cracked, clouded, or leaking.

  The cap will not close, the primer is split or stuck, or the 1. Remove the battery, wipe away oil, and inspect the cap, primer, indicator, and

• The lithium battery or charger shows abnormal heat, swelling, cracking, electrolyte, hissing, odor, sparks, or smoke.

  The lithium battery or charger shows abnormal heat, 1. Stop charging or using the pack immediately and unplug the charger if it is safe to

• After chain or bar work, the cover will not sit flush, the bar will not align, or the locking knob cannot begin correctly.

  After chain or bar work, the cover will not sit flush, the 1. Remove the battery, put on gloves, place the saw on a firm surface, loosen the

• FM-13: FM-13 CUTTING IS SLOW, ROUGH, OR REQUIRES EXCESSIVE PRESSURE

  Cutting is slow, rough, or requires excessive pressure due to dull or damaged chain or improper tension.

• FM-05: If the saw remains dead with proven power and free controls, leave the housing

  4. If the saw remains dead with proven power and free controls, leave the housing

• FM-15: FM-15 CHAIN JUMPS OFF OR DERAILS DURING USE

  Chain jumps off or derails from the guide bar during use, causing unsafe operation.

• FM-22: FM-22 BATTERY OR CHARGER IS HOT, SWOLLEN, CRACKED, LEAKING, OR SMOKING

  Battery or charger exhibits hazardous conditions such as heat, swelling, cracking, leakage, or smoke.

• FM-12: FM-12 CHAIN MOVES BUT WILL NOT CUT BECAUSE IT IS INSTALLED BACKWARD

  Chain moves around the guide bar but does not cut because it is installed backward.

• FM-09: FM-09 CHAIN IS TOO TIGHT, BINDS BY HAND, OR BAR AND CHAIN OVERHEAT

  FM-09 CHAIN IS TOO TIGHT, BINDS BY HAND, OR BAR AND CHAIN OVERHEAT

• FM-23: FM-23 SAW IS WET OR SHOWS SMOKE, SPARKS, BURNING ODOR, MELTING, OR EXPOSED WIRING

  FM-23 SAW IS WET OR SHOWS SMOKE, SPARKS, BURNING ODOR, MELTING, OR EXPOSED WIRING

• FM-16: FM-16 MANUAL OILER DOES NOT DELIVER OIL TO THE BAR AND CHAIN

  Manual oiler does not deliver oil to the bar and chain, causing dry operation and increased wear.

• FM-14: FM-14 SAW CUTS CROOKED OR PULLS TO ONE SIDE

  FM-14 SAW CUTS CROOKED OR PULLS TO ONE SIDE

• FM-01: FM-01 BATTERY PACK WILL NOT INSERT, LATCH, OR RELEASE

  Battery pack will not insert, latch, or release properly, preventing tool operation.

• fm-p14-b-93c34c19: Boundary: If the tension controls will not turn or clamp,

  Boundary: If the tension controls will not turn or clamp,

• FM-08: FM-08 CHAIN IS LOOSE, SAGS, OR WILL NOT HOLD TENSION

  FM-08 CHAIN IS LOOSE, SAGS, OR WILL NOT HOLD TENSION