BLACK+DECKER LCS1020 Reparasjonsmanual

Omfattende reparasjonsveiledning for BLACK+DECKER LCS1020 trådløs motorsag, inkludert feilsøking, vedlikehold og reparasjonsinstruksjoner for 24 vanlige feil.

$39.99

Sist oppdatert Aug 22, 2026, 10:05 AM

Om denne manualen

Omfattende reparasjonsveiledning for BLACK+DECKER LCS1020 trådløs motorsag, inkludert feilsøking, vedlikehold og reparasjonsinstruksjoner for 24 vanlige feil.

0% rapporterte vellykkede reparasjoner

Price

$39.99

Full manual inkluderer

root cause analysis
tools needed
step-by-step repair procedure
diagrams
exploded views
post-repair checks

Forhåndsvisning av innholdsfortegnelse

Black+decker Lcs1020
De seks viktigste tingene
Hva denne modellen faktisk har
Indikator- og signaloversikt
Modellrevisjonsadvarsel
Kuttebanen
Normal bruksekvens
Normal oppførsel som kan se ut som en feil
Hva denne modellen ikke har
Sagen
Ubrukelig
FM-08 KJEDE ER LØS, HENGER ELLER VIL IKKE HOLDE STRAMMING
FM-20 UNORMAL SLIPING, RASLING ELLER STERK VIBRASJON
FM-09 KJEDE ER FOR STRAM, BINDER FOR HÅND, ELLER SKINNE OG KJEDE OVEROPPHETES
FM-21 STYRESKINNE, SAGKJEDE, SLIRE ELLER KUTTETILBEHØR ER

This preview shows only a portion of the complete repair manual. Purchase to access the full repair documentation, downloadable PDF and detailed repair procedures.

Støttet modell

Vis modellens feilsøkingsside

BLACK+DECKER

Bdcr20c

Vis detaljer

BLACK+DECKER

Bdcdd12c

Vis detaljer

BLACK+DECKER

Ld120va

Vis detaljer

BLACK+DECKER

Bdci20c

Vis detaljer

The battery will not slide fully into the tool, click into place, stay latched, or release normally.

Vis detaljer

The chain travels around the bar but only rubs the wood, produces almost no chips, and will not enter the cut.

Vis detaljer

The saw chain leaves the guide-bar groove, hangs from the bar, or comes off the drive sprocket.

Vis detaljer

Bar oil forms a fresh puddle, runs from the cap, or appears from the body while the saw is idle or stored.

Vis detaljer

The cap will not close, the primer is split or stuck, or the oil-level indicator is cracked, clouded, or leaking.

Vis detaljer

The saw cuts slowly, makes fine dust instead of chips, chatters in the kerf, or must be pushed hard despite judging sharpness.

Vis detaljer

The lock-off or trigger will not move freely, does not return, responds intermittently, or the motor continues after the trigger is released.

Vis detaljer

The reservoir contains oil but the chain stays dry, the primer gives no visible result, or the bar oil path remains dry.

Vis detaljer

Saw dead with charged pack

Vis detaljer

The saw makes new grinding, clacking, rattling, or strong vibration during no-load running or cutting.

Vis detaljer

After chain or bar work, the cover will not sit flush, the bar will not align, or the locking knob cannot begin correctly.

Vis detaljer

The bar is bent or cracked, chain links or cutters are broken, or the guide-bar scabbard is split, missing, or will not stay on.

Vis detaljer

Motor runs, chain does not

Vis detaljer

The guide bar steers sideways in the cut or the kerf curves even though the workpiece is supported and the saw is held square.

Vis detaljer

Chain moves but does not cut

Vis detaljer

The guide bar cannot be withdrawn from the kerf, the chain is trapped, or the workpiece closes on the saw.

Vis detaljer

The lithium battery or charger shows abnormal heat, swelling, cracking, electrolyte, hissing, odor, sparks, or smoke.

Vis detaljer

The chain hangs below the guide bar, can be pulled too far from the rail, or becomes loose again after adjustment.

Vis detaljer

Liquid entered the tool, the housing emits smoke or sparks, plastic melts, a burning odor appears, or wiring or contacts are exposed.

Vis detaljer

The chain is hard to pull around the bar, the bar becomes unusually hot, or smoke appears without an electrical odor.

Vis detaljer

The front hand guard, front or rear handle, main housing, ribbed bumper, fastener, battery well, or another external part is cracked, loose, or missing.

Vis detaljer

A tool-free knob is frozen, cross-threaded, spins without effect, will not clamp the bar, or cannot hold the set tension.

Vis detaljer

The motor can be heard, but the chain remains stationary or only twitches while the trigger is held.

Vis detaljer

FM-01: FM-01 BATTERY PAKKE VIL IKKE SETTES INN, LÅSES ELLER FRIGJØRES

Sammendrag

Battery-pakke vil ikke settes inn, låses eller slippes riktig, noe som hindrer verktøyets drift.

Full repair guide includes

Root Cause Analysis
Required Tools
Replacement Parts
Step-by-step Repair Procedure
Safety Precautions
Verification Checklist

BLACK+DECKER LCS1020 Reparasjonsmanual

Manual information

Om denne manualen

Full manual inkluderer

Forhåndsvisning av innholdsfortegnelse

Støttet modell

Relaterte modeller

Vanlige symptomer

Feilmoduser

Relaterte manualer