DCS575

Model number: DCS575

Also known as: DCS575, DEWALT DCS575, DCS575 60V MAX Circular Saw

• Dewalt Dcs575 Circular Saw Repair Maintenance Manual 6bfeb09a

• The Blade Cannot Be Removed, Installed, Or Clamped

  The blade lock will not engage, the clamping screw will not loosen or tighten, or the blade and washers cannot be assembled securely.

• Blade Speed Or Cutting Force Is Below Normal

  The blade turns, but speed or cutting force is below normal in a correctly supported wood cut.

• The Battery Pack Will Not Seat, Latch, Or Release

  The battery will not slide in, latch, stay latched, or release normally.

• The Bevel Setting Or 90 Degree Cut Accuracy Is Wrong

  The bevel lever will not lock, the quadrant setting moves, or a cut is not square when the pointer is at zero.

• The Depth Adjustment Will Not Set, Lock, Or Hold

  The shoe will not set or clamp at depth, or cutting depth changes during use.

• The Electric Brake Does Not Stop The Blade Promptly

  After trigger release, the blade coasts too long or stopping is inconsistent.

• The Saw Grinds, Knocks, Rattles, Or Vibrates Abnormally

  The running saw has harsh noise or vibration not caused by the workpiece.

• The Trigger Or Lock-Off Control Does Not Work Safely

  The lock-off will not block or release the trigger, or the trigger sticks or switches unreliably.

• The Saw Starts, Then Cuts Out With The Trigger Held

  The saw starts, then stops while the trigger stays held, under load or at no load.

• The Blade Slips, Wobbles, Or Runs Incorrectly

  The blade shifts, runs off-center, rubs the guard, or its teeth oppose the guard arrow.

• The Saw Will Not Start Or Produce Any Response

  - Pressing lock-off and trigger produces no motor or blade motion - the worklight may stay dark.

• The Lower Blade Guard Does Not Retract Or Close Freely

  The lower guard binds, moves slowly, rubs, stays open, or fails to cover the blade.

• FM-13: The Bevel Setting Or 90 Degree Cut Accuracy Is Wrong

  The bevel lever will not lock, the quadrant setting moves, or a cut is not square when the pointer is at zero.

• FM-09: The Blade Slips, Wobbles, Or Runs Incorrectly

  The blade shifts, runs off-center, rubs the guard, or its teeth oppose the guard arrow.

• FM-08: The Blade Cannot Be Removed, Installed, Or Clamped

  The blade lock will not engage, the clamping screw will not loosen or tighten, or the blade and washers cannot be assembled securely.

• FM-16: Immediate Battery, Electrical, Liquid, Or Structural Hazard

  Smoke, sparks, burning odor, liquid, battery damage, dangerous heat, or exposed structure is present.

• FM-05: The Trigger Or Lock-Off Control Does Not Work Safely

  The lock-off will not block or release the trigger, or the trigger sticks or switches unreliably.

• FM-03: The Saw Starts, Then Cuts Out With The Trigger Held

  The saw starts, then stops while the trigger stays held, under load or at no load.

• FM-15: The Saw Grinds, Knocks, Rattles, Or Vibrates Abnormally

  The running saw has harsh noise or vibration not caused by the workpiece.

• FM-11: The Worklight Does Not Work Normally

  The worklight is dark or flickers, or its delay after trigger release is abnormal.

• FM-01: The Saw Will Not Start Or Produce Any Response

  - Pressing lock-off and trigger produces no motor or blade motion - the worklight may stay dark.

• FM-02: The Battery Pack Will Not Seat, Latch, Or Release

  The battery will not slide in, latch, stay latched, or release normally.

• FM-06: The Electric Brake Does Not Stop The Blade Promptly

  After trigger release, the blade coasts too long or stopping is inconsistent.

• FM-14: The Saw Or Battery Overheats Or Heat Shutoff Repeats

  The saw or pack gets abnormally hot, loses output, or stops during a supported cut.