搜索维修指南
在知识库中查找维修指南、手册、症状和错误代码。
motor 和轴转动，但刀片在垫圈上卡滞或滑动，正常支撑切割时发生。
已安装充电电池组，但触发器无工作灯、motor声音或冲击锤动作。
Pemicu menyalakan area kerja, tetapi motor tetap diam dan landasan tidak bergerak.
WORKLIGHT COMES ON, BUT THE MOTOR WILL NOT START
The motor can be heard, but the front output remains still in both directions with the bit removed.
工作灯亮起但Motor和锯片不启动
A straight bit traces a visible circle at no load instead of rotating on a stable centerline.
Bright repeated arcing or sharp crackling is visible at the rear vents while the tool runs.
The trigger returns normally and power drops, but the anvil repeatedly coasts instead of stopping promptly.
锯或齿轮箱异常发热或有热味但无烟无火花
360度除尘口卡住或松动，或兼容的软管/接头无法保持连接。
The external structure is visibly cracked, loose, crushed, melted, or missing material even if the saw still runs.
The quick-release collar binds, will not move fully forward, or stays forward after release.
A straight bit or socket visibly orbits, shakes, or runs off-center during a brief no-load test.
After trigger release, the bit or square drive coasts noticeably longer than normal before stopping.
battery无法完全滑入手柄、锁定、保持或正常释放。
Motosega morta con pacco carico
The bar is bent or cracked, chain links or cutters are broken, or the guide-bar scabbard is split, missing, or will not stay on.
The cool tool starts, then stops during a brief no-load test or light fastening task before heat builds.
The direction lever will not reach forward, reverse, or center lock, or the selected position does not hold.
FM-08: FM-08 链条松弛、下垂或无法保持张力
FM-01: 无 LED 或 motor 响应 通过 FM-01 验证充电、电池安装、中心锁位置、触点和触发器
FM-06: MOTOR运转但刀片不转
FM-05: FM-05 SPEED WILL NOT VARY, SURGES, OR CUTS ERRATICALLY
FM-07: FM-07: A compatible pack stops on the rails, will not reach full
FM-27: FM-27 工具或电池组过热，或热关闭重复发生
FM-04: FM-04 工具启动后冷却时断电
FM-10: FM-10 紧固输出弱或无冲击动作
FM-11: FM-11 刹车无法快速停止输出
FM-15: FM-15 工具或BATTERY过热或反复关机
FM-12: FM-12 钻头卡滞、卡死或扭转钻机
FM-05: 如果锯子在确认有电且控制自由的情况下仍无反应，保持机壳关闭，
FM-04: FM-04 运行时间非常短或工具突然关闭
FM-05: FM-05 触发器卡滞或速度控制不安全
FM-32: Røyk kommer ut av verktøyet under drift
FM-03: The Saw Starts, Then Cuts Out With The Trigger Held
FM-04: FM-04 钻机冷却时断电
FM-08: FM-08 夹头无法打开、关闭或接受钻头
FM-11: FM-11 速度或扭矩在正确设置下偏低
FM-14: FM-14 钻机空载时磨损或振动