搜索维修指南
在知识库中查找维修指南、手册、症状和错误代码。
El paquete está hinchado, goteando, siseando, humeando, quemándose, aplastado, mojado o abierto.
锯子启动后，扳机保持按下时断电
The trigger returns normally and power drops, but the anvil repeatedly coasts instead of stopping promptly.
THE BATTERY WILL NOT SEAT, LATCH, RELEASE, OR STAY SECURE
The motor can be heard, but the front output remains still in both directions with the bit removed.
The direction lever will not reach forward, reverse, or center lock, or the selected position does not hold.
360度除尘口卡住或松动，或兼容的软管/接头无法保持连接。
The bar is bent or cracked, chain links or cutters are broken, or the guide-bar scabbard is split, missing, or will not stay on.
The external structure is visibly cracked, loose, crushed, melted, or missing material even if the saw still runs.
Trigger binds, fails to return, changes speed erratically, or does not stop the drive.
Tool rotates, but a seated fastener gets little torque or no normal impact pulse.
A straight bit traces a visible circle at no load instead of rotating on a stable centerline.
WORKLIGHT COMES ON, BUT THE MOTOR WILL NOT START
After trigger release, the bit or square drive coasts noticeably longer than normal before stopping.
BATTERY WILL NOT CHARGE
Bezpieczne proste wiertło i czysta praca nie eliminują głośnego dźwięku lub drgań bez obciążenia.
Charger green LED stays on
Chłodna wiertarka zaczyna działać, a następnie zatrzymuje się podczas krótkiego testu bez obciążenia lub lekkiej pracy.
Chuck clicks while tightening
Narzędzie, akumulator lub ładowarka nagrzewa się nadmiernie lub ochrona wielokrotnie zatrzymuje pracę.
FM-16: 立即的BATTERY安全隐患
fm-5-1-2: FM-20 外壳开裂、分裂、穿孔或接缝处打开
FM-03: The Saw Starts, Then Cuts Out With The Trigger Held
FM-16: FM-16 立即BATTERY、充电器或工具危险
FM-15: FM-15 BATTERY 存储断开连接时快速失电
FM-05: 如果锯子在确认有电且控制自由的情况下仍无反应，保持机壳关闭，
FM-22: FM-22 BATTERY 或充电器过热、膨胀、开裂、泄漏或冒烟
FM-18: FM-18 油从盖子、油箱或机壳泄漏
FM-21: FM-21 导轨、锯链、护套或切割附件损坏
fm-3-1: FM-07 导板、链条或链轮罩无法安装或就位
FM-02: 电池组无法安装、锁定或释放
FM-05: FM-05 SPEED WILL NOT VARY, SURGES, OR CUTS ERRATICALLY
FM-06: 电池组恢复至室温后仍存在冷热延迟
FM-16: FM-16 BIT WILL NOT RELEASE, OR A SHORT OR BROKEN BIT IS TRAPPED
FM-18: FM-18 A KNOWN-STRAIGHT BIT SHOWS VISIBLE WOBBLE OR RUNOUT
FM-27: FM-27 工具或电池组过热，或热关闭重复发生
fm-3-2: CHARGE-STATUS INDICATOR GIVES NO RESPONSE AFTER A CONFIRMED FULL CHARGE
fm-2-1-4: FM-22 BIT BINDS, TOOL STALLS, TWISTS, OR STOPS IN THE WORK
FM-07: Låst battery vil ikke frigjøres
FM-04: FM-04 钻机冷却时断电