Sổ Tay Sửa Chữa & Bảo Trì Cưa Tròn DEWALT DCS575
Cưa tròn không dây DEWALT DCS575 60V MAX 7-1/4 INCH. Xác nhận DCS575 và loại trên nhãn đánh giá trước khi sử dụng hướng dẫn này. Công cụ sử dụng bộ pin lithium-ion 60V MAX FLEXVOLT tương thích.
$29.99
Cập nhật lần cuối Aug 17, 2026, 7:51 AM
Manual information
Giới thiệu hướng dẫn này
Cưa tròn không dây DEWALT DCS575 60V MAX 7-1/4 INCH. Xác nhận DCS575 và loại trên nhãn đánh giá trước khi sử dụng hướng dẫn này. Công cụ sử dụng bộ pin lithium-ion 60V MAX FLEXVOLT tương thích.
0% sửa chữa thành công được báo cáo
Nhận sách hướng dẫn sửa chữa đầy đủ — tiết kiệm 250 US$–290 US$
$29.99
Hướng dẫn đầy đủ bao gồm
- root cause analysis
- tools needed
- step-by-step repair procedure
- diagrams
- exploded views
- post-repair checks
Xem trước mục lục
- Đọc Trước
- Thông Số Kỹ Thuật
- Cách Thiết Bị Này Hoạt Động
- Bảng Chẩn Đoán Nhanh
- An Toàn
- Các Bộ Phận và Điều Khiển
- Từ Triệu Chứng Đến Nguyên Nhân
- Chế Độ Hỏng FM-01 đến FM-16
- Bộ Phân Loại Linh Kiện và Bộ Kit
- 16 chế độ lỗi
- Chẩn đoán Battery và lưỡi cưa
- Kiểm tra bảo vệ dưới và phanh
- Ranh giới an toàn cho chủ sở hữu
This preview shows only a portion of the complete repair manual. Purchase to access the full repair documentation, downloadable PDF and detailed repair procedures.
Nguyên nhân gốc có thể
- Battery pack is discharged, too hot or cold, or faulty
- Pack is not fully seated or its contacts are obstructed
- Trigger lock-off button is not fully released or is damaged
- Trigger movement is blocked or damaged
- Internal switch, controller, or motor fault
- Rails contain packed dry debris or are damaged
- Battery case or tool rails are cracked or distorted
- Latch or release button is jammed or broken
- Wrong or incompatible battery pack is being tried
- Battery interface or housing is impact-damaged
- Pack protection opened for charge or temperature
- Blade was pinched, bound, or overloaded by the cut
- Pack is loose or the contacts are intermittent under vibration
- Blocked vents or heavy loading caused thermal protection
- Internal control or motor fault
- Battery charge or output is too low for the load
- Blade is dull, dirty, damaged, or unsuitable
- Blade rotation, size, arbor, or speed rating is incorrect
- Cut depth is excessive or feed pressure is too high
- Motor, bearing, or electronic drive fault
- Dry debris obstructs the trigger or lock-off button
- Trigger or lock-off is cracked or impact-damaged
- Trigger return or lock-off spring mechanism has failed
- Liquid or contamination entered the control area
- Internal switch or electronic control fault
- Battery is nearly depleted or protection is unstable
- Trigger does not return fully to the off position
- Blade or spindle has excessive drag, looseness, or damage
- Electronic brake or controller has failed
- Motor or internal wiring fault
- Sawdust or chips obstruct the guard path
- Guard is bent, cracked, or misassembled
- Retracting lever, pivot, or spring is damaged
- Blade or clamp parts rub the guard at some angles or depths
- Guard mechanism requires qualified adjustment or replacement
- Blade lock is not aligned with the spindle
- Wrong direction used on the right-hand screw
- Sawdust packed around clamp washer or spindle
- Spindle lock or threads are damaged internally
- Blade is mounted in the wrong rotation direction
- Blade size or 5/8 inch arbor hole is incorrect
- Outer washer is reversed or the screw is loose
- Blade is bent, cracked, dirty, or below the required speed rating
- Spindle, clamp washer, bearing, or shoe is damaged
- Depth lever is not fully loosened or tightened
- Sawdust is packed in the shoe slide or pivot
- Depth scale, lever, pivot, or shoe is bent or damaged
- Fastener or clamping surface is worn or loose
- Internal or structural adjustment repair is required
- Battery charge is too low for a valid test
- Trigger is not moving far enough to activate the light
- Lens area is blocked by dry debris
- LED or wiring is damaged
- Switch or electronic control fault
- Workpiece support lets the kerf close on the blade
- Blade is dull, damaged, dirty, or installed incorrectly
- Depth or bevel lever is loose or set incorrectly
- Saw is twisted, forced, or restarted in the kerf
- Fastener, knot, or offcut pinches the blade
- Bevel lever is not fully tightened
- Sawdust blocks the quadrant or shoe pivot
- Pointer or calibration stop is out of adjustment
- Shoe, quadrant, or pivot is bent from impact
- Blade or spindle runout is creating a false angle
- Vents are blocked by sawdust or the saw is covered
- Blade is dull or the feed load is excessive
- Battery is hot, cold, low, damaged, or unsuitable
- Cut depth, support, or material is overloading the saw
- Motor, bearing, controller, or battery fault
- Blade is bent, cracked, loose, dirty, or mounted off-center
- Guard or shoe is rubbing the blade
- Sawdust or a foreign object is caught near the blade or guard
- Spindle, bearing, gearcase, or motor is damaged
- Housing, handle, shoe, or fastener is loose or cracked
- Battery is swollen, leaking, cracked, or venting
- Liquid entered the battery, switch, motor, or housing
- Internal electrical short or overheating component
- Guard, shoe, handle, or housing exposes parts
- Impact or fire damage makes the saw unsafe
Model được hỗ trợ
Model liên quan
DEWALT
Xem chi tiết
DEWALT
Xem chi tiết
DEWALT
Xem chi tiết
DEWALT
Xem chi tiết
DEWALT
Xem chi tiết
DEWALT
Xem chi tiết
DEWALT
Xem chi tiết
DEWALT
Xem chi tiết
DEWALT
Xem chi tiết
DEWALT
Xem chi tiết
DEWALT
Xem chi tiết
DEWALT
Xem chi tiết
Triệu chứng phổ biến
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Chế độ lỗi
Tóm tắt
- Nhấn nút khóa và cò súng không tạo ra chuyển động motor hoặc lưỡi cưa - đèn làm việc có thể không sáng.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Tóm tắt
battery không trượt vào, khóa, giữ khóa hoặc thả ra bình thường.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Tóm tắt
Cưa khởi động rồi dừng khi cò vẫn giữ, có tải hoặc không tải.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Tóm tắt
Lưỡi quay nhưng tốc độ hoặc lực cắt thấp hơn bình thường trong cắt gỗ được hỗ trợ đúng cách.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Tóm tắt
Khóa cò không chặn hoặc thả cò, hoặc cò bị kẹt hoặc chuyển đổi không đáng tin cậy.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Tóm tắt
Sau khi thả cò, lưỡi quay quá lâu hoặc dừng không nhất quán.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Tóm tắt
Bảo vệ dưới bị kẹt, di chuyển chậm, cọ xát, mở, hoặc không che phủ lưỡi.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Tóm tắt
Khóa lưỡi không khóa được, screw kẹp không nới hoặc siết được, hoặc không thể lắp lưỡi và vòng đệm chắc chắn.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Tóm tắt
Lưỡi lệch, chạy lệch tâm, cọ xát bảo vệ, hoặc răng lưỡi ngược mũi tên bảo vệ.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Tóm tắt
Giày không thiết lập hoặc kẹp được độ sâu, hoặc độ sâu cắt thay đổi khi sử dụng.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Tóm tắt
Đèn làm việc tối hoặc nhấp nháy, hoặc thời gian trễ sau khi thả cò không bình thường.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Tóm tắt
Lưỡi kẹt, dừng trong khe cắt, bị đẩy lùi hoặc không thể khởi động lại an toàn.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Tóm tắt
Cần nghiêng không khóa, thiết lập góc di chuyển, hoặc cắt không vuông khi con trỏ ở số không.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Tóm tắt
Cưa hoặc pin quá nóng bất thường, mất công suất hoặc dừng khi cắt được hỗ trợ.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Tóm tắt
Cưa chạy phát ra tiếng ồn hoặc rung lắc mạnh không do vật liệu.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Tóm tắt
Có khói, tia lửa, mùi cháy, chất lỏng, hư hại battery, nhiệt nguy hiểm hoặc cấu trúc lộ ra.
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
Hướng dẫn liên quan
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết
Xem chi tiết