수리 가이드 검색
지식 베이스에서 수리 가이드, 매뉴얼, 증상 및 오류 코드를 찾으세요.
A known-good compatible charger begins its normal charging cycle, but the cycle repeatedly stops, restarts, faults, or continues abnormally without reaching completion.
A hand-tightened bit slips, visibly wobbles, or its tip runs off center when the drill turns.
Smoke, flame, severe arcing, liquid, battery damage, melted contacts, exposed parts, or cracked structure.
The bit passed initial insertion, but backs out, falls free, or loses drive while the chuck body stays secure.
The forward/reverse button sticks, commands the wrong rotation, or center does not lock the trigger.
The trigger binds, the drill continues after release, or speed does not follow trigger pressure safely.
충전기 녹색 LED가 깜박이지 않거나, 절대 켜지지 않거나, battery가 방전 상태로 남아 있습니다.
충전기 후면 키홀 슬롯과 하우징이 온전함에도 불구하고 battery 삽입 또는 제거 중에 충전기가 흔들리거나 미끄러지거나 screws에서 들리거나 당겨짐.
The housing, handle, rails, nose, vents, lens, or accessory mount is cracked or loose.
Spoušť se plně nevrací ven, nebo motor/kotouč běží i po uvolnění spouště.
The chuck still rotates, but a new mechanical grind, knock, scrape, tight spot, or severe vibration remains with the bit removed and is not ordinary motor or brake sound.
The tool or pack becomes unusually hot, or operation stops only after heat builds.
Bright repeated arcing or sharp crackling is visible at the rear vents while the tool runs.
CORDON D’ALIMENTATION OU PRISE ENDOMMAGÉE, LÂCHE, BRÛLÉE, OU CHAUDE
The tool starts and runs at no load, but stops abruptly on an ordinary fastener with no jam or twist.
A tool-free knob is frozen, cross-threaded, spins without effect, will not clamp the bar, or cannot hold the set tension.
The tool works until the pack, handle, or tool is bumped or shifted, then loses power.
The chain is hard to pull around the bar, the bar becomes unusually hot, or smoke appears without an electrical odor.
Smoke, burning odor, melting, liquid, active sparks, swelling, hissing, or severe pack damage is present.
The bar is bent or cracked, chain links or cutters are broken, or the guide-bar scabbard is split, missing, or will not stay on.
fm-3-5: CHARGING STARTS, THEN STOPS OR NEVER REACHES NORMAL COMPLETION
FM-16: FM-16 즉각적인 BATTERY, 전기, 출력 또는 구조적 위험
FM-28: 후면 통풍구에서 심한 BRUSH 아크 또는 귓속말 소리 발생
FM-19: 온전한 슬롯에도 벽걸이형 충전기가 흔들리거나 분리됨
FM-09: FM-09 A 고정된 비트가 미끄러지거나 흔들리거나 무부하에서 회전함
FM-27: FM-27 공구 또는 팩 과열, 또는 열 셧다운 반복
FM-17: FM-17 THE BIT SLIPS OR PULLS OUT UNDER LOAD
FM-31: FM-31 발이 휘거나 균열, 느슨하거나 평평하게 앉지 않음
FM-32: FM-32 먼지 추출이 약하거나 먼지 경로가 막힘
FM-27: 공구에 새로운 연삭음, 노크, 고착 또는 심한 진동 발생