수리 가이드 검색
지식 베이스에서 수리 가이드, 매뉴얼, 증상 및 오류 코드를 찾으세요.
A straight bit traces a visible circle at no load instead of rotating on a stable centerline.
At no load the motor starts, but speed has a dead band, surges, cuts out, or ignores trigger pressure.
Prosty bit pozostaje zaciskany, ale obraca się poza środek lub korpus uchwytu ma widoczne luzy.
The trigger returns normally and power drops, but the anvil repeatedly coasts instead of stopping promptly.
WORKLIGHT COMES ON, BUT THE MOTOR WILL NOT START
The motor can be heard, but the front output remains still in both directions with the bit removed.
With a charged pack installed and direction selected, the trigger produces no light, sound, or anvil movement.
A hand-tightened bit slips, visibly wobbles, or its tip runs off center when the drill turns.
A correct-looking bit will not enter fully or can be pulled out after the collar is released.
The chuck jaws bind, will not release a bit, close unevenly, or cannot grip a straight round shank.
The forward/reverse button sticks, commands the wrong rotation, or center does not lock the trigger.
Wiertarka działa stabilnie, ale wierci wolno lub nie może wkręcić normalnego elementu mocującego przy prawidłowym ustawieniu.
Uchwyt otwiera się i zamyka, ale wiertło ślizga się, wypada lub jest wyrzucane podczas normalnej pracy.
WIERTARKA NIE REAGUJE NA MOTOR ANI UCHWYT
Charger green LED stays on
LED 또는 motor 반응 없음
Naładowany, zatrzaśnięty battery i normalne polecenie spustu nie powodują obrotu uchwytu.
Smoke, liquid, swelling, or major damage
THE BATTERY OR CHARGER WILL NOT BEGIN OR COMPLETE A CHARGE
THE BATTERY WILL NOT SEAT, LATCH, RELEASE, OR STAY SECURE
FM-07: FM-07: A compatible pack stops on the rails, will not reach full
FM-18: FM-18 A KNOWN-STRAIGHT BIT SHOWS VISIBLE WOBBLE OR RUNOUT
FM-05: FM-05 SPEED WILL NOT VARY, SURGES, OR CUTS ERRATICALLY
fm-2-1-4: FM-22 BIT BINDS, TOOL STALLS, TWISTS, OR STOPS IN THE WORK
FM-16: FM-16 BIT WILL NOT RELEASE, OR A SHORT OR BROKEN BIT IS TRAPPED
FM-17: FM-17 THE BIT SLIPS OR PULLS OUT UNDER LOAD
FM-21: FM-21 INTERNAL GRINDING, KNOCKING, OR SCRAPING AT NO LOAD
FM-14: FM-14 드릴이 무부하에서 갈리거나 진동함
FM-01: LED 또는 motor 반응 없음 FM-01: 충전, 장착, 중앙 잠금 위치, 접점 및 트리거 확인
FM-09: FM-09 A 고정된 비트가 미끄러지거나 흔들리거나 무부하에서 회전함
FM-01: FM-01 드릴에 MOTOR 또는 척 반응 없음
FM-10: FM-10 직선 비트가 흔들리거나 척이 느슨함
FM-12: FM-12 비트가 걸리거나 스톨되거나 드릴을 비틀음
FM-04: FM-04 작동 시간이 매우 짧거나 도구가 갑자기 꺼짐
FM-03: Fm-03 Battery가 충전되지 않음
FM-05: FM-05 트리거가 걸리거나 속도 제어가 불안정함
FM-06: FM-06 방향 제어가 선택되지 않음
FM-08: FM-08 척이 열리지 않거나 닫히지 않거나 비트를 수용하지 않음
FM-09: FM-09 비트가 미끄러지거나 고정되지 않음
FM-11: FM-11 올바른 설정에도 속도 또는 토크가 낮음