CRAFTSMAN CMCS500M1 修理マニュアル
CRAFTSMAN CMCS500M1 コードレス丸ノコの包括的な修理マニュアルで、トラブルシューティング、修理手順、安全警告、仕様を特徴とし、DIYメンテナンスと故障解決に役立ちます。
$39.99
最終更新日 Aug 8, 2026, 11:12 AM
Manual information
このマニュアルについて
CRAFTSMAN CMCS500M1 コードレス丸ノコの包括的な修理マニュアルで、トラブルシューティング、修理手順、安全警告、仕様を特徴とし、DIYメンテナンスと故障解決に役立ちます。
報告された修理成功率 0%
$39.99
完全版マニュアルの内容
- root cause analysis
- tools needed
- step-by-step repair procedure
- diagrams
- exploded views
- post-repair checks
目次プレビュー
- クラフトマン CMCS500M1 V20 コードレス丸ノコ
- クラフトマン CMCS500M1
- V20 コードレス 6-1/2インチ 丸ノコキット - 17の異なる故障モード
- このモデルの実際の特徴
- インジケーターと信号マップ
- モデル改訂警告
- パワーと切断経路
- 通常の使用手順
- 故障のように見える正常動作
- このモデルにないもの
- FM-17 煙、火花、液体、熱、またはBATTERY損傷
- FM-08 切断が遅い、詰まる、停止する、焼ける、またはささくれる
- FM-09 丸ノコがキックバック、登る、または後退する
- FM-01、FM-02、FM-03、FM-05、FM-15、FM-17。
- FM-02、FM-17。
This preview shows only a portion of the complete repair manual. Purchase to access the full repair documentation, downloadable PDF and detailed repair procedures.
考えられる根本原因
- Trigger or lock-off is jammed by debris
- Trigger return spring or switch has failed
- Control or wiring is shorted
- Trigger has been taped, tied, or modified
- Impact damage has distorted the handle or controls
- Electronic protection stopped overload, heat, or deep discharge
- Battery latch or contacts are intermittent
- Battery is weak or not fully charged
- Blade is dull, pinched, or set too deep
- Switch, motor, wiring, or gear train is failing
- Blade bolt or outer washer is loose or assembled wrong
- Blade is not seated on the spindle
- Blade bolt or washer is damaged
- Gear train or spindle has stripped or broken
- Spindle lock damage is interfering with the drive
- Blade is bent, cracked, chipped, or wrong bore
- Blade, washer, or bolt is dirty or misassembled
- Blade bolt is loose
- Shoe or guard is bent into the blade path
- Spindle or bearing has side play or damage
- Blade is dull, damaged, dirty, or wrong for wood
- Cut depth is excessive
- Kerf closes because the work is unsupported
- Depth or bevel lock is loose
- Saw is forced before full speed or against the cut line
- Kerf closes on the blade from poor support
- Blade is dull, damaged, or misaligned
- Saw is twisted or restarted with teeth engaged
- Depth or bevel lock shifted
- Operator is behind the blade line or pulling backward
- Blade is loose, warped, or not seated
- Shoe is not square to the blade at zero
- Bevel scale or 90-degree alignment needs calibration
- Shoe is bent or work support is uneven
- Guide technique or blade choice causes wandering
- Sawdust or resin is packed in a pivot or scale
- Lever or knob is not fully released or tightened
- Threads, cam, pivot, or scale are worn
- Shoe or linkage is bent from impact
- External adjustment hardware is cracked or missing
- Lock is not aligned with the spindle position
- Left-hand bolt is being turned the wrong direction
- Hex recess or wrench is rounded
- Bolt, washer, or spindle threads are dirty or damaged
- Spindle lock mechanism is broken
関連カテゴリー
関連モデル
一般的な症状
詳細を見る
詳細を見る
詳細を見る
詳細を見る
詳細を見る
詳細を見る
詳細を見る
詳細を見る
詳細を見る
詳細を見る
詳細を見る
詳細を見る
故障モード
概要
batteryを挿入するとすぐにブレードが回転し始め、トリガーを離しても丸ノコが停止しない。これは重大な安全上の危険であり、直ちに対処が必要です。
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
概要
FM-05 負荷時に丸ノコが停止または断続的に動作する問題。
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
概要
FM-06 MOTORは動作するがブレードが回転しない問題。
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
概要
FM-07 ブレードがぶれる、擦れる、振動する、または研削音がする
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
概要
ブレードは回転するが、丸ノコの送りが悪い、詰まる、木材が焼ける、または通常の切断中に過度にささくれる切断性能の問題。損傷や怪我を防ぐために直ちに使用を停止することが推奨されます。
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
概要
丸ノコがキックバックを示し、突然持ち上がったり、操作側に跳ねたり、切り込みから外れたり、刃の挟み込みやねじれにより後退する。
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
概要
FM-10 切断が直角でない、または傾斜角が不正確な問題。
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
概要
深さまたは傾斜調整機構が動かず、ロックできず、設定を保持できないため、不正確な切断や安全でない操作を引き起こす。
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
概要
FM-12 ブレードBOLTまたはスピンドルロックが作動しない問題。
Full repair guide includes
- Root Cause Analysis
- Required Tools
- Replacement Parts
- Step-by-step Repair Procedure
- Safety Precautions
- Verification Checklist
関連マニュアル
詳細を見る
詳細を見る
詳細を見る
詳細を見る
詳細を見る
詳細を見る
詳細を見る
詳細を見る
詳細を見る
詳細を見る
詳細を見る
詳細を見る