BLACK+DECKER LCS1020 Repair Manual

This comprehensive repair manual covers the BLACK+DECKER LCS1020 20V MAX 10-inch cordless chainsaw, detailing 24 distinct failure modes with troubleshooting, root causes, repair steps, and verification procedures. It guides users through diagnosing and fixing common issues related to battery insertion, chain tension, cutting performance, oiling system, safety components, and electrical faults.

$39.99

最終更新日 Aug 1, 2026, 1:13 AM

このマニュアルについて

0% Reported Successful Repair

Price

$39.99

完全版マニュアルの内容

root cause analysis
tools needed
step-by-step repair procedure
diagrams
exploded views
post-repair checks

目次プレビュー

Detailed diagnostics for 24 failure modes
Step-by-step repair instructions
Battery pack troubleshooting and repair
Chain installation and tension adjustment
Oiling system maintenance and repair
Electrical and motor fault diagnosis
Safety component inspection and replacement

This preview shows only a portion of the complete repair manual. Purchase to access the full repair documentation, downloadable PDF and detailed repair procedures.

考えられる根本原因

Debris, resin, or chips in the battery rails
Damaged or swollen battery housing
Jammed release button or latch
Bent tool battery well or contact support
Wrong or incompatible battery pack
Resin, dirt, or debris around the controls
Cracked or distorted rear-handle housing
Broken return spring or linkage
Worn or welded trigger-switch contacts
Loose internal wiring
New chain has stretched during break-in
Bar-adjust locking knob was not tightened
Chain tension was set incorrectly
Worn chain, bar groove, or tensioner parts
Chain was adjusted while hot
Chain was over-tensioned
Chain or bar is dry
Guide-bar groove or oil hole is clogged
Wrong or damaged chain is installed
Bar rails or drive links are burred
Knob was overtightened or cross-threaded
Resin, chips, or dirt in the threads
Tensioner tab is outside its slot
Stripped knob, bolt, cover, or tensioner teeth
Cracked sprocket cover
Chain is off the drive sprocket
Drive links are jammed in the bar groove
Broken chain or damaged drive links
Stripped or broken drive sprocket
Internal gearbox failure
Chain was fitted with cutters facing backward
Chain was reversed during cleaning or replacement
Direction marks were overlooked
Cover was assembled before orientation was checked
Dull, chipped, or damaged cutters
Incorrect chain tension
Dry bar and chain
Chain contacted soil, stone, wire, or a nail
Worn guide bar or wrong chain
Cutters on one side are duller or shorter
Unequal depth gauges
Burred or uneven guide-bar rails
Bent guide bar
Uneven or incorrect chain tension
Chain was too loose
Worn or damaged drive links
Bent, pinched, or badly worn guide-bar groove
Damaged drive sprocket
Cover, tensioner, or locking knob did not hold
Oil level is too low
Primer was not pressed fully or long enough
Guide-bar oil hole or groove is clogged
Wrong, waste, or overly thick oil
Blocked or failed primer or internal feed path
Wood closes on and pinches the bar
Motor or gearbox has excessive internal load
Log or limb support let the kerf close
Tensioned branch moved during the cut
Saw was twisted in the kerf
Cut sequence did not match how the log was supported
Bar or chain was already crooked or loose
Oil cap is loose, cross-threaded, or dirty
Reservoir was overfilled
Saw was stored on its side or in heat
Cap seal, primer, reservoir, or oil tube is cracked
Housing seam is damaged
Impact or age cracked the plastic
Cap threads or seal are damaged
Primer bulb hardened, split, or detached
Indicator window is cracked or clouded
Reservoir neck or housing is distorted
Loose bar, cover, or handle hardware
Chain is dry, loose, damaged, or off the sprocket
Debris is trapped under the cover
Worn drive sprocket or gearbox
Motor bearing or internal housing fault
Chain hit soil, stone, metal, or a hard foreign object
Bar was bent in a pinch or impact
Chain derailed or broke
Wrong chain or bar was installed
Scabbard was crushed, cut, or lost
Damaged or aged battery cells
Shorted or contaminated terminals
Wrong or failed charger
Charging outside the allowed temperature range
Impact, water, fire, or internal electrical failure
Water or oil entered electrical areas
Internal short, stalled motor, or wiring failure
Damaged battery contact block
Melted switch or motor insulation
Cracked housing exposed live components
Drop, impact, or crush damage
Loose or missing fastener
Age or chemical damage to plastic
Overtightened or stripped mount
Using the guard or scabbard as a carrying handle
Chain is not fully in the guide-bar groove
Cutters face the wrong direction
Chain is not around the drive sprocket
Bar slot is not on the mounting bolt misaligned
Tensioner was not returned to its stop or tab is

対応モデル

モデルのトラブルシューティングページを見る

BLACK+DECKER

Bdcr20c

詳細を見る

BLACK+DECKER

Bdcdd12c

詳細を見る

BLACK+DECKER

Ld120va

詳細を見る

BLACK+DECKER

Bdci20c

詳細を見る

FM-01: FM-01 BATTERYパックが挿入、ラッチ、またはリリースされない

概要

Batteryパックが正しく挿入、ラッチ、またはリリースされず、工具の動作を妨げます。

Full repair guide includes

Root Cause Analysis
Required Tools
Replacement Parts
Step-by-step Repair Procedure
Safety Precautions
Verification Checklist

BLACK+DECKER LCS1020 Repair Manual

Manual information

このマニュアルについて

完全版マニュアルの内容

目次プレビュー

考えられる根本原因

対応モデル

関連モデル

故障モード

関連マニュアル