搜索维修指南
在知识库中查找维修指南、手册、症状和错误代码。
One or more green charge-status segments stay on, stay missing, or report an implausible level even though the battery charges and delivers normal low-load runtime.
La lumière rouge continue de clignoter tandis que l'indicateur jaune reste allumé même après que la batterie battery et le chargeur ont atteint naturellement une température ambiante autorisée.
可以聽到motor運轉，但鋸片保持靜止、啟動遲或打滑，無法跟隨motor轉動。
Motor 運轉但鋸片冇轉
WORKLIGHT COMES ON, BUT THE MOTOR WILL NOT START
The bit passed initial insertion, but backs out, falls free, or loses drive while the chuck body stays secure.
The bit rotates, but no impact pulses begin when a correct fastener provides normal resistance.
The direction button jams, will not hold center lock, or the tool runs in only one direction.
At no load the motor starts, but speed has a dead band, surges, cuts out, or ignores trigger pressure.
Pemicu macet, gagal kembali, atau motor tetap menyala setelah dilepaskan.
Narzędzie, akumulator lub ładowarka nagrzewa się nadmiernie lub ochrona wielokrotnie zatrzymuje pracę.
Bright repeated arcing or sharp crackling is visible at the rear vents while the tool runs.
Kerah menarik tetapi aksesori yang terpasang tidak keluar, atau potongan patah terjebak di chuck.
With no fastener load, the bare or correctly fitted output sounds harsh, binds, knocks, or shakes abnormally.
Uchwyt otwiera się i zamyka, ale wiertło ślizga się, wypada lub jest wyrzucane podczas normalnej pracy.
The cool tool starts, then stops during a brief no-load test or light fastening task before heat builds.
The quick-release collar is stuck, has limited travel, or does not spring back after it is pulled.
A straight bit or socket visibly orbits, shakes, or runs off-center during a brief no-load test.
Chłodna wiertarka zaczyna działać, a następnie zatrzymuje się podczas krótkiego testu bez obciążenia lub lekkiej pracy.
Nach Loslassen des Abzugs schlägt das Blatt deutlich länger als normal weiter aus.
FM-06: MOTOR運轉但鋸片不轉
fm-3-3: LES SEGMENTS D'ÉTAT DE CHARGE SONT BLOQUÉS, PARTIELS OU IMPLAUSIBLES ALORS QUE LA SORTIE D'ÉNERGIE EST NORMALE
FM-06: HOT/COLD DELAY REMAINS AFTER THE PACK RETURNS TO ROOM TEMPERATURE
FM-09: FM-09 鑽頭滑動或唔會保持夾緊
fm-2-1-3: FM-14 CHUCK COLLAR WILL NOT PULL OR RETURN
FM-15: FM-15 A 1/4-IN. HEX BIT WILL NOT INSERT OR LOCK
FM-21: FM-21 INTERNAL GRINDING, KNOCKING, OR SCRAPING AT NO LOAD
FM-03: FM-03 TRIGGER STICKS OR THE MOTOR CONTINUES AFTER RELEASE
FM-17: FM-17 THE BIT SLIPS OR PULLS OUT UNDER LOAD
FM-20: FM-20 CHUCK ROTATES, BUT IMPACT ACTION IS ABSENT UNDER LOAD
FM-18: FM-18 A KNOWN-STRAIGHT BIT SHOWS VISIBLE WOBBLE OR RUNOUT
FM-19: FM-19 MOTOR RUNS, BUT THE CHUCK AND ANVIL DO NOT ROTATE
FM-07: FM-07: A compatible pack stops on the rails, will not reach full
FM-04: FM-04 ELECTRIC BRAKE MISSES OR THE ANVIL COASTS TOO LONG
FM-05: FM-05 SPEED WILL NOT VARY, SURGES, OR CUTS ERRATICALLY
FM-13: FM-13 WORKLIGHT IS DEAD, DIM, OR INTERMITTENT WHILE THE MOTOR RUNS
fm-2-1-4: FM-22 BIT BINDS, TOOL STALLS, TWISTS, OR STOPS IN THE WORK
fm-2-1-2: FM-06 DIRECTION CONTROL JAMS, WILL NOT LOCK OFF, OR LOSES ONE DIRECTION
FM-02: FM-02 WORKLIGHT COMES ON, BUT THE MOTOR WILL NOT START
FM-16: FM-16 BIT WILL NOT RELEASE, OR A SHORT OR BROKEN BIT IS TRAPPED