수리 가이드 검색
지식 베이스에서 수리 가이드, 매뉴얼, 증상 및 오류 코드를 찾으세요.
충전기 녹색 LED가 깜박이지 않거나, 절대 켜지지 않거나, battery가 방전 상태로 남아 있습니다.
The trigger binds or does not spring fully OFF, or the motor keeps running after the trigger is released.
Pemicu macet, gagal kembali, atau motor tetap menyala setelah dilepaskan.
TRIGGER STICKS, WILL NOT RETURN, OR MOTOR KEEPS RUNNING
BATTERY WILL NOT CHARGE
A seated battery shows no charge response, or charge never reaches a usable full state.
Pakiet nie ładuje się lub lampka ładowarki pozostaje wyłączona lub pokazuje nienormalny czerwony wzór.
Laddaren startar inte eller slutför inte laddning, eller dess gröna lampa beter sig onormalt.
Battery or charger feels warm
THE BATTERY OR CHARGER WILL NOT BEGIN OR COMPLETE A CHARGE
A compatible V20 battery starts onto the tool rails but binds before reaching the normal seated and latched position.
A straight bit or the empty chuck shows repeatable side-to-side runout at low no-load speed after the bit has been centered and tightened correctly.
battery가 물리적으로 래치된 상태를 유지하지만 도구 또는 battery가 일반 작업 자세로 움직일 때 motor, LED 또는 둘 다가 꺼졌다가 다시 켜짐.
battery를 제거하고 척이 비어 있는 상태에서 슬리브를 돌리면 척을 손으로 조이거나 풀기에 충분한 잠금력을 제공하지 않고 스핀들 및 motor가 자유롭게 회전합니다.
motor가 작동하는 소리는 들리지만 척은 움직이지 않거나 독립적으로 멈추거나 정상적인 구동력을 전달하지 않고 자유 회전함.
The chuck jaws open and close normally, but a straight compatible bit rotates or pulls out during moderate drilling or driving.
The chuck still rotates, but a new mechanical grind, knock, scrape, tight spot, or severe vibration remains with the bit removed and is not ordinary motor or brake sound.
The collar moves and holds a low numbered setting, but the clutch does not ratchet before a test fastener is overdriven in suitable scrap material.
The collar moves normally, but the clutch ratchets before a suitable fastener reaches normal depth at appropriate settings, or it audibly slips when drill mode is correctly selected.
The direction selector is centered, but the trigger still depresses enough to start the motor or the center position cannot reliably prevent activation.
FM-03: FM-03 BATTERY 또는 충전기가 충전을 시작하거나 완료하지 못함
FM-03: Fm-03 Battery가 충전되지 않음
FM-03: FM-03 TRIGGER STICKS OR THE MOTOR CONTINUES AFTER RELEASE
FM-03: Fm-03 Battery가 충전되지 않음
FM-03: BATTERY가 충전기에 갇히거나 해제되지 않음
FM-03: FM-03 BATTERY가 충전을 시작하거나 완료하지 않음
FM-01: 검증된 BATTERY로 드릴/드라이버가 시작되지 않음
FM-05: 키트 BATTERY가 충전을 시작하거나 완료하지 않음
FM-06: 도구 또는 BATTERY가 움직일 때 전원 차단됨
FM-17: 2단 속도 선택기가 범위 간 이동하지 않음
FM-17: FM-17 STYRERELSE ELLER KJEDE ER KLEMT ELLER FASTKILLET I TRE
FM-19: 모드/토크 칼라가 회전하거나 정렬되지 않음
FM-21: 클러치가 너무 일찍 해제되거나 드릴 모드에서 미끄러짐
FM-22: 척이 손으로 열리거나 닫히지 않거나 비트가 해제되지 않음
FM-26: MOTOR는 작동하지만 척이 회전하지 않거나 구동력을 잃음
FM-27: 공구에 새로운 연삭음, 노크, 고착 또는 심한 진동 발생
FM-28: 무부하 정상 작동에도 불구하고 드릴링 또는 고정이 느림
fm-2-1: FM-01 BATTERY가 정상 호환 공구 또는 충전기에 완전히 삽입되지 않음
FM-20: FM-20 UNORMAL SLIPING, RASLING ELLER STERK VIBRASJON
FM-22: 가벼운 사용 중 샌더 하우징이 비정상적으로 뜨거워짐