修理ガイドを検索
ナレッジベース全体で修理ガイド、マニュアル、症状、エラーコードを検索できます。
The cool tool starts, then stops during a brief no-load test or light fastening task before heat builds.
A correct-looking bit will not enter fully or can be pulled out after the collar is released.
After chain or bar work, the cover will not sit flush, the bar will not align, or the locking knob cannot begin correctly.
A compatible-looking pack will not slide fully into the handle, click, or stay retained.
batteryは装着位置に達するが、リリースボタンを押さずに引き抜かれたり持ち上がったり保持力を失う。目視できるパックとチャージャーの構造は正常に見える。
チャックが停止しbatteryを外した状態で、チャックを手で回してギアを整列させてもトップセレクターがレンジ1またはレンジ2に完全に動かない。
The drill stalls, binds, shuts down, or has low power
With the battery removed from every tool and charger, the charge-status button cannot be pressed normally, remains depressed or has broken away.
Spoušť se plně nevrací ven, nebo motor/kotouč běží i po uvolnění spouště.
The clamp lever opens normally, but the installed blade remains trapped in the front clamp.
Narzędzie, akumulator lub ładowarka nagrzewa się nadmiernie lub ochrona wielokrotnie zatrzymuje pracę.
A straight bit or socket visibly orbits, shakes, or runs off-center during a brief no-load test.
Chłodna wiertarka zaczyna działać, a następnie zatrzymuje się podczas krótkiego testu bez obciążenia lub lekkiej pracy.
După eliberarea declanșatorului, lama continuă să se miște vizibil mai mult decât normal.
Uchwyt otwiera się i zamyka, ale wiertło ślizga się, wypada lub jest wyrzucane podczas normalnej pracy.
With no fastener load, the bare or correctly fitted output sounds harsh, binds, knocks, or shakes abnormally.
The quick-release collar is stuck, has limited travel, or does not spring back after it is pulled.
The accessory catches or stops in the material and the tool reacts sharply in the hand.
The motor runs normally, but the LED is dead, dim, or intermittent with trigger use.
The direction button jams, will not hold center lock, or the tool runs in only one direction.
FM-15: FM-15 A 1/4-IN. HEX BIT WILL NOT INSERT OR LOCK
FM-11: FM-11 ドリルがスタック、固着、停止、または出力不足
FM-04: FM-04 ツールが始動するが冷却中に停止する
FM-08: FM-08 LA LAME INSTALLÉE NE SE LIBÈRE PAS
FM-17: 2速セレクターがレンジ間で動かない
fm-3-1: FM-07 ガイドバー、チェーン、またはスプロケットカバーが取り付けられないまたは座らない
fm-3-1: 充電状態ボタンが詰まっている、壊れている、または戻らない場合
FM-03: FM-03 BATTERYまたは充電器が充電を開始または完了しない
FM-04: FM-04 冷却中にドリルが停止する
FM-09: FM-09 ビット、ソケット、または出力ドライブが振れるまたはぶれる
FM-09: FM-09 ビットが滑る、または固定されない
FM-15: FM-15 工具またはBATTERYが過熱または冷却気流が遮断されている
FM-27: FM-27 ツールまたはパックが過熱する、または熱によるシャットダウンが繰り返される
fm-3-1-4: FM-15 工具、BATTERY、または充電器が過熱する
FM-31: FM-31 フットが曲がっている、ひび割れている、緩んでいる、または平らに座らない
fm-2-1-3: FM-14 CHUCK COLLAR WILL NOT PULL OR RETURN
FM-21: FM-21 INTERNAL GRINDING, KNOCKING, OR SCRAPING AT NO LOAD
FM-20: FM-20 CHUCK ROTATES, BUT IMPACT ACTION IS ABSENT UNDER LOAD
FM-17: FM-17 THE BIT SLIPS OR PULLS OUT UNDER LOAD
FM-13: FM-13 WORKLIGHT IS DEAD, DIM, OR INTERMITTENT WHILE THE MOTOR RUNS