BDCI20C

Numero modello: BDCI20C

Conosciuto anche come: BDCI202, BDCI20C

• Black Decker Bdci20c 20v Max Impact Driver Repair Manual

• The collar pulls, but the bit will not come out, or a short/broken piece is recessed in the chuck.

  The collar pulls, but the bit will not come out, or a 1. Remove the pack; point the nose down; hold the collar open and pull only a

• The bit passed initial insertion, but backs out, falls free, or loses drive while the chuck body stays secure.

  The bit passed initial insertion, but backs out, falls free, 1. Release the trigger, remove the pack, and inspect the bit shank and retention

• At no load the motor starts, but speed has a dead band, surges, cuts out, or ignores trigger pressure.

  At no load the motor starts, but speed has a dead band, 1. Remove the pack and dry-clean trigger, rails, terminals, and vents.

• The trigger returns normally and power drops, but the anvil repeatedly coasts instead of stopping promptly.

  The trigger returns normally and power drops, but the 1. Remove the pack and dry-clean the trigger opening; confirm free full return.

• The accessory catches or stops in the material and the tool reacts sharply in the hand.

  The accessory catches or stops in the material and the 1. Release the trigger and control the tool until all motion stops.

• The bit rotates, but no impact pulses begin when a correct fastener provides normal resistance.

  The bit rotates, but no impact pulses begin when a 1. Remove the pack and fit a correct impact-rated bit that matches an

• The trigger lights the work area, but the motor stays silent and the quick-release chuck does not turn.

  The trigger lights the work area, but the motor stays 1. Release trigger, remove the pack and bit, and let tool and pack cool.

• With a charged pack installed and direction selected, the trigger produces no light, sound, or anvil movement.

  With a charged pack installed and direction selected, 1. Release trigger; center the control; remove the pack and screen for heat,

• A straight bit traces a visible circle at no load instead of rotating on a stable centerline.

  A straight bit traces a visible circle at no load instead of 1. Remove the pack, clean the chuck bore, and inspect the first bit for bend or

• WORKLIGHT COMES ON, BUT THE MOTOR WILL NOT START

  FM-02 WORKLIGHT COMES ON, BUT THE MOTOR WILL NOT FM-09 POWER CUTS OUT WHEN THE PACK OR TOOL IS

• The direction button jams, will not hold center lock, or the tool runs in only one direction.

  The direction button jams, will not hold center lock, or 1. Release the trigger and wait for complete stop; remove the battery.

• NO WORKLIGHT OR MOTOR RESPONSE

  FM-01 NO WORKLIGHT OR MOTOR RESPONSE FM-08 BATTERY WILL NOT RELEASE FROM THE TOOL

• FM-20: FM-20 CHUCK ROTATES, BUT IMPACT ACTION IS ABSENT UNDER LOAD

  FM-20 CHUCK ROTATES, BUT IMPACT ACTION IS ABSENT UNDER LOAD

• FM-16: FM-16 BIT WILL NOT RELEASE, OR A SHORT OR BROKEN BIT IS TRAPPED

  The chuck collar pulls but the bit will not come out, or a short or broken bit piece is recessed inside the chuck.

• FM-04: FM-04 ELECTRIC BRAKE MISSES OR THE ANVIL COASTS TOO LONG

  The electric brake misses or the anvil coasts too long after releasing the trigger, causing delayed stopping.

• FM-17: FM-17 THE BIT SLIPS OR PULLS OUT UNDER LOAD

  FM-17 THE BIT SLIPS OR PULLS OUT UNDER LOAD

• FM-13: FM-13 WORKLIGHT IS DEAD, DIM, OR INTERMITTENT WHILE THE MOTOR RUNS

  The motor runs normally but the LED worklight is dead, dim, or flickers intermittently during trigger use.

• FM-19: FM-19 MOTOR RUNS, BUT THE CHUCK AND ANVIL DO NOT ROTATE

  FM-19 MOTOR RUNS, BUT THE CHUCK AND ANVIL DO NOT ROTATE

• FM-15: FM-15 A 1/4-IN. HEX BIT WILL NOT INSERT OR LOCK

  A correct-looking 1/4-inch hex bit will not insert fully or lock in the chuck.

• FM-07: A compatible pack stops on the rails, will not reach full

  Keep the trigger in center lock and inspect both pack and tool for

• FM-22 BIT BINDS, TOOL STALLS, TWISTS, OR STOPS IN THE WORK

  The accessory bit binds, causing the tool to stall, twist sharply, or stop unexpectedly in the work.

• FM-06 DIRECTION CONTROL JAMS, WILL NOT LOCK OFF, OR LOSES ONE DIRECTION

  The direction control jams, will not lock off, or the tool runs in only one direction.

• FM-05: FM-05 SPEED WILL NOT VARY, SURGES, OR CUTS ERRATICALLY

  Motor starts at no load but speed control is erratic, with dead zones, surging, or cutting out unexpectedly.

• FM-01: FM-01 NO WORKLIGHT OR MOTOR RESPONSE

  No worklight or motor response when the trigger is pressed, indicating a complete power failure.