failure mode
FM-18: ब्लेड रुकता है, फंसता है, पिंच होता है, या कट में आरी पीछे की ओर किक करती है
ब्लेड केर्फ द्वारा फंसाया या धीमा किया जाता है, आरी उठती है या ऑपरेटर की ओर पीछे की ओर धकेलती है, या दांत सामग्री में फंसे होने पर पुनः शुरू करने का प्रयास होता है।
Diagnostic overview
ब्लेड केर्फ द्वारा फंसाया या धीमा किया जाता है, आरी उठती है या ऑपरेटर की ओर पीछे की ओर धकेलती है, या दांत सामग्री में फंसे होने पर पुनः शुरू करने का प्रयास होता है।
Likely Root Causes
- Workpiece is supported so the kerf closes and pinches the blade
- Blade is dull, dirty, bent, wrong, too deep, or twisted off the line
- Saw was started against the work or forced, turned, or backed in the cut
- Wet, knotty, treated, or unstable wood is loading the blade
Quick Checks
- The saw enters at full speed and completes a supported straight scrap cut without kerf closure, stall, twist, lift, or kickback.
Repair Preview
- Release the trigger immediately, hold the saw firmly until the blade stops and guard closes, then remove the battery before freeing the blade.
- Support the work close to the cut so the cutoff cannot sag into the kerf, and remove nails, wire, unstable pieces, and binding forces.
- - Inspect and replace a dull, dirty, bent, damaged, or wrong blade - set depth to about one-half tooth below the material and secure both adjustment levers.
- Reposition the shoe flat and straight, bring the blade to full speed before contact, and feed at a rate that lets the blade cut without laboring or turning
- - Make one supported scrap cut - if binding occurs with correct support, blade, depth, alignment, and feed, stop and route guard, shoe, spindle, and drive ali
This is a preview of the troubleshooting guidance included in the full repair manual.
Common Fixes
- बेवेल लीवर, क्वाड्रंट, पॉइंटर, और शून्य कैलिब्रेशन
- शू और संरचनात्मक पिवट्स
- लकड़ी काटने वाला सर्कुलर आरी ब्लेड
- मुख्य हैंडल, सहायक हैंडल, और सुरक्षात्मक संरचना
- गहराई लीवर, गाइड, और स्केल
- गियरकेस, गियर्स, बेयरिंग्स, या स्पिंडल
- निचला ब्लेड गार्ड, रिट्रैक्टिंग लीवर, पिवट, और स्प्रिंग
- गियरकेस, गियर, बियरिंग, और स्पिंडल
- 7-1/4-इंच लकड़ी काटने वाला ब्लेड
Related symptoms
ब्लेड रुकता है, फंसता है, पिंच होता है, या कट में आरी पीछे की ओर किक करती है
ब्लेड केर्फ द्वारा फंसाया या धीमा किया जाता है, आरी उठती है या ऑपरेटर की ओर पीछे की ओर धकेलती है, या दांत सामग्री में फंसे होने पर पुनः शुरू करने का प्रयास होता है।
Included in the full manual
- root cause analysis
- tools needed
- step-by-step repair procedure
- diagrams
- exploded views
- post-repair checks
Public pages show a preview only. Purchase the full manual to download complete repair steps, diagrams, and verification procedures.