البحث في أدلة الإصلاح
اعثر على أدلة الإصلاح والأدلة والأعراض ورموز الأخطاء في قاعدة المعرفة.
The battery will not slide in, click into place, release, or remain secure in the handle.
Bladet håller inte fastspänt
Med klämspaken fungerande går ett korrekt blad inte i helt eller klarar handdragstest.
The battery shows a credible high charge or has just completed a proven charge, remains fully latched and still gives no response in a known-good compatible tool while stationary.
battery يبقى مقفلًا ماديًا، لكن motor، LED، أو كلاهما ينقطع ويعود عند تحريك الأداة أو battery خلال الوضعية العادية للعمل.
Tombol maju/mundur tidak masuk, kunci tengah gagal, atau alat berjalan ke arah yang salah.
Rękaw uchwytu nie obraca się wystarczająco, aby przesunąć szczęki lub przyjąć normalny prosty bit.
The saw cuts slowly, makes fine dust instead of chips, chatters in the kerf, or must be pushed hard despite judging sharpness.
冲击级1/2英寸套筒无法完全安装、保持或从方形输出驱动拉出。
The direction button jams, will not hold center lock, or the tool runs in only one direction.
The accessory or fastener stops in the work and the tool stalls, twists, or cannot be withdrawn normally.
The accessory catches or stops in the material and the tool reacts sharply in the hand.
Kerah menarik tetapi aksesori yang terpasang tidak keluar, atau potongan patah terjebak di chuck.
The quick-release collar is stuck, has limited travel, or does not spring back after it is pulled.
The chuck still rotates, but a new mechanical grind, knock, scrape, tight spot, or severe vibration remains with the bit removed and is not ordinary motor or brake sound.
With no accessory load, the front drive makes abnormal metallic noise or feels rough.
The accessory slips from the fastener, damages it, breaks it, or drives it beyond the intended seat.
Rotation and impact pulses are steady, but a normal fastener advances much more slowly than expected.
battery V20 بدرجة حرارة الغرفة مثبت بالكامل في شاحن معتمد، لكن الشحن الطبيعي لا يبدأ أو الحزمة لا تصل إلى مؤشر الشحن المكتمل.
تم تركيب حزمة مشحونة، لكن الزناد لا ينتج ضوء عمل، صوت motor، أو حركة السندان.
FM-02: FM-02 BATTERY لن يجلس، يقفل، يطلق، أو يبقى آمنًا
FM-06: انقطاع الطاقة عند تحريك الأداة أو BATTERY
FM-08: FM-08 الفك لا يفتح، يغلق، أو يقبل قطعة
FM-08: FM-08 لا يناسب المقبس نصف بوصة، لا يمسك، أو لا يطلق
FM-13: FM-13 القطع بطيء، خشن، أو يتطلب ضغطًا مفرطًا
fm-2-1-2: FM-06 DIRECTION CONTROL JAMS, WILL NOT LOCK OFF, OR LOSES ONE DIRECTION
fm-2-1-2: FM-07 الشفرة لا تدخل أو تبقى مثبتة
FM-30: FM-30 القطع غير مربع مع ضبط الميل على صفر
fm-2-1-4: FM-22 BIT BINDS, TOOL STALLS, TWISTS, OR STOPS IN THE WORK
fm-5-1-2: FM-20 الهيكل الخارجي متشقق، مقسوم، مثقوب، أو مفتوح عند الوصلة
fm-2-1-3: FM-14 CHUCK COLLAR WILL NOT PULL OR RETURN
FM-02: الحزمة لا تثبت، لا تقفل، أو لا تتحرر
FM-06: FM-06 الزناد أو قفل الإيقاف عالق، متقطع، أو لا يوقف المنشار
FM-11: FM-11 كانت BATTERY مبللة، مغمورة، أو معرضة لسائل موصل أو تآكلي
FM-11: FM-11 الشفرة تنحرف، تنثني، أو تنكسر
FM-12: FM-12 السلسلة تتحرك لكن لا تقطع لأنها مركبة بالعكس
FM-13: FM-13 WORKLIGHT IS DEAD, DIM, OR INTERMITTENT WHILE THE MOTOR RUNS
FM-14: FM-14 المثقاب يطحن أو يهتز بدون حمل
FM-12: FM-12 المنشار يقفز، يهتز، أو يركل أثناء القطع
FM-08: FM-08 فكوك الكلش بدون مفتاح لا تفتح، تغلق، تطلق، أو تمسك