搜索维修指南
在知识库中查找维修指南、手册、症状和错误代码。
The cool tool starts, then stops during a brief no-load test or light fastening task before heat builds.
The drill stalls, binds, shuts down, or has low power
After chain or bar work, the cover will not sit flush, the bar will not align, or the locking knob cannot begin correctly.
A compatible-looking pack will not slide fully into the handle, click, or stay retained.
battery 达到插入位置但会被拉出、抬起或失去固定，且未按下释放按钮。可见的电池组和充电器结构完好。
With the chuck stopped and battery removed, the top selector cannot be moved fully into range 1 or range 2, even after the chuck is turned by hand to align the gears.
With the battery removed from every tool and charger, the charge-status button cannot be pressed normally, remains depressed or has broken away.
A correct-looking bit will not enter fully or can be pulled out after the collar is released.
Klämspaken öppnas normalt, men det installerade bladet sitter fast i framklämman.
Spoušť se plně nevrací ven, nebo motor/kotouč běží i po uvolnění spouště.
Narzędzie, akumulator lub ładowarka nagrzewa się nadmiernie lub ochrona wielokrotnie zatrzymuje pracę.
A straight bit or socket visibly orbits, shakes, or runs off-center during a brief no-load test.
Chłodna wiertarka zaczyna działać, a następnie zatrzymuje się podczas krótkiego testu bez obciążenia lub lekkiej pracy.
Efter att avtryckaren släppts fortsätter bladet att slå märkbart längre än normalt.
Uchwyt otwiera się i zamyka, ale wiertło ślizga się, wypada lub jest wyrzucane podczas normalnej pracy.
With no fastener load, the bare or correctly fitted output sounds harsh, binds, knocks, or shakes abnormally.
Bright repeated arcing or sharp crackling is visible at the rear vents while the tool runs.
Kerah menarik tetapi aksesori yang terpasang tidak keluar, atau potongan patah terjebak di chuck.
The quick-release collar is stuck, has limited travel, or does not spring back after it is pulled.
Den löpande sågen hoppar, vibrerar mot arbetsstycket, fastnar eller sparkar bakåt eller åt sidan.
FM-04: FM-04 工具启动后冷却时断电
FM-15: FM-15 A 1/4-IN. HEX BIT WILL NOT INSERT OR LOCK
FM-11: FM-11 钻机卡滞、卡住、停机或功率不足
FM-08: FM-08 安装的刀片无法释放
FM-17: IL SELETTORE A DUE VELOCITÀ NON SI SPOSTA TRA LE GAMME
fm-3-1: FM-07 导板、链条或链轮罩无法安装或就位
fm-3-1: 充电状态按钮卡住、损坏或无法返回
FM-04: FM-04 钻机冷却时断电
FM-03: FM-03 BATTERY 或充电器无法开始或完成充电
FM-09: FM-09 批头、套筒或输出驱动摇摆或偏心运行
FM-09: FM-09 钻头滑动或无法保持夹紧
FM-15: FM-15 工具或 BATTERY 过热或冷却气流受阻
FM-27: FM-27 工具或电池组过热，或热关闭重复发生
fm-3-1-4: FM-15 工具、BATTERY或充电器过热
FM-31: FM-31 底座弯曲、开裂、松动或无法平放
fm-2-1-3: FM-14 CHUCK COLLAR WILL NOT PULL OR RETURN
FM-21: FM-21 INTERNAL GRINDING, KNOCKING, OR SCRAPING AT NO LOAD
FM-15: FM-15 链条使用中跳脱或脱轨
FM-21: FM-21 导轨、锯链、护套或切割附件损坏
FM-16: FM-16 立即BATTERY、充电器或工具危险