搜索维修指南
在知识库中查找维修指南、手册、症状和错误代码。
The pack is fully seated, the release button is pressed, and the battery still cannot be slid out without excessive force.
钻机无法启动，尽管使用了充满电且已知良好的 BATTERY
Klemmen vil ikke bevege seg
At no load the motor starts, but speed has a dead band, surges, cuts out, or ignores trigger pressure.
充电、锁定的battery和正常触发命令无旋转、无冲击或无LED。
免工具刀片夹具释放杆无法完全打开或安全关闭。
BATTERY WILL NOT SEAT, LATCH, OR RELEASE
battery无法完全滑入手柄、锁定、保持或正常释放。
Po usunięciu battery i bez zamontowanego wiertła uchwyt nie obraca się normalnie ręcznie lub wydaje się zacięty.
The torque collar binds, will not stay on a setting, or the clutch slips or locks at every position.
充电且锁定的battery和正常触发器操作无夹头旋转。
可以听到motor运转声，但夹头静止或不正常旋转。
标准1/4英寸动力槽冲击批头无法插入、保持锁定或从六角夹持器释放。
空载正常，但批头、套筒或紧固件卡滞、打滑或扭曲工具。
The quick-release collar binds, will not move fully forward, or stays forward after release.
The accessory or fastener stops in the work and the tool stalls, twists, or cannot be withdrawn normally.
Med klämspaken fungerande går ett korrekt blad inte i helt eller klarar handdragstest.
Bright repeated arcing or sharp crackling is visible at the rear vents while the tool runs.
Rotation and impact pulses are steady, but a normal fastener advances much more slowly than expected.
360度除尘口卡住或松动，或兼容的软管/接头无法保持连接。
FM-01: FM-01 工具无旋转、冲击或LED响应
FM-05: FM-05 BATTERY 在存储和断开连接时快速失电
FM-05: FM-05 SPEED WILL NOT VARY, SURGES, OR CUTS ERRATICALLY
FM-06: FM-06 刀片夹杠杆无法打开或关闭
fm-1-1: FM-01 钻机无法启动，尽管使用了充满电且已知良好的 BATTERY
fm-1-1: 锁定的 BATTERY 无法从接收器释放
FM-02: FM-02 BATTERY 无法就位、锁定或释放
FM-04: FM-04 运行时间非常短或工具突然关闭
FM-07: FM-07 扭矩环无法移动、保持或控制离合器打滑
FM-10: FM-10 MOTOR 运行但夹头不转
FM-11: FM-11 刀片偏移、弯曲或断裂
FM-12: FM-12 链条移动但因安装反向而不切割
FM-12: FM-12 附件凸轮卡住、卡滞或扭曲工具
FM-13: FM-13 夹头或主轴静止时转动困难
FM-15: FM-15 链条使用中跳脱或脱轨
FM-18: FM-18 油从盖子、油箱或机壳泄漏
FM-21: FM-21 INTERNAL GRINDING, KNOCKING, OR SCRAPING AT NO LOAD
FM-08: FM-08 链条松弛、下垂或无法保持张力
fm-3-1: FM-07 导板、链条或链轮罩无法安装或就位
fm-2-1-4: FM-22 BIT BINDS, TOOL STALLS, TWISTS, OR STOPS IN THE WORK