CMCF800C1

型号： CMCF800C1

亦称： Craftsman, CMCF800C1

• Craftsman Cmcf800c1 Repair Manual

• TRIGGER STICKS, WILL NOT RETURN, OR MOTOR KEEPS RUNNING

  FM-03 TRIGGER STICKS, WILL NOT RETURN, OR MOTOR KEEPS RUNNING

• 工具完全无反应 - 无LED或MOTOR

  FM-01 工具完全无电 - 无LED或MOTOR FM-09 电源在电池组或工具中断

• The release button moves poorly or the pack remains trapped on the tool rails.

  The release button moves poorly or the pack remains 1. Center direction and support tool and pack so no weight binds the rails.

• The forward/reverse button will not seat, center lock-off fails, or the tool runs the wrong way.

  The forward/reverse button will not seat, center lock-off 1. Release the trigger, wait for full stop, and remove the pack.

• The trigger returns and motor power ends, but the chuck repeatedly coasts much longer than normal.

  The trigger returns and motor power ends, but the chuck 1. Remove the accessory, fit a charged known-good pack, and point safely.

• 已安装充电电池组，但触发器无工作灯、motor声音或冲击锤动作。

  已安装充电的battery电池组，但拉动触发器无工作灯、motor声音或冲击锤动作。

• A known-straight, fully retained 1/4-in. hex bit traces a visible circle at no load.

  A known-straight, fully retained 1/4-in. hex bit traces a 1. Remove the pack; inspect and clean a known-straight bit and its shank.

• 符合标准的冲击级1/4英寸六角配件无法完全插入或锁定快速释放夹头。

  一个完好且符合冲击标准的1/4英寸六角配件无法 1. 调整中心方向，取出电池组，检查配件柄部和凹槽。

• The tool starts and runs at no load, but stops abruptly on an ordinary fastener with no jam or twist.

  The tool starts and runs at no load, but stops abruptly 1. Release the trigger, remove the pack, and prove the fastener is not

• 无紧固负载时，速度波动、有死区、断断续续或忽略触发行程。

  无紧固件负载时，速度波动，有死区，断断续续，或忽略触发行程。1. 取下钻头，安装已知良好电池组，进行一次短暂无负载触发扫动。

• The bit rotates, but a real fastening load never produces the normal impact sound or pulses.

  The bit rotates, but a real fastening load never produces 1. Fit a charged known-good pack and the correct impact-rated accessory.

• Bright repeated arcing or sharp crackling is visible at the rear vents while the tool runs.

  Bright repeated arcing or sharp crackling is visible at the 1. Release the trigger, remove the pack, and let the motor area cool.

• FM-22: 驱动输出低，尽管旋转和冲击稳定

  FM-22 驱动输出低，尽管旋转和冲击稳定

• FM-23: 紧固件打滑、剥离、断裂或过度拧紧

  FM-23 紧固件打滑、剥离、断裂或过度驱动

• FM-29: 外壳、手柄、导轨、前端、通风口或挂钩安装损坏

  FM-29 外壳、手柄、导轨、前端、通风口或挂钩安装损坏

• FM-15: 正确的1/4英寸六角钻头无法插入或锁定

  FM-15 A 正确的1/4英寸六角钻头无法插入或锁定

• FM-09: 移动电池组或工具时电源中断

  Fm-09 电源在电池组或工具移动时断电

• FM-25: FM-25 工具在负载下关闭，无机械卡滞

  FM-25 工具在负载下关闭，无机械卡滞

• FM-01: FM-01 工具完全无反应 - 无LED或MOTOR

  尽管安装了充电的battery电池组，工具完全无反应，无LED或motor响应。

• FM-13: 工作灯远超正常余辉时间仍保持点亮

  FM-13 工作灯远超正常余辉时间仍保持点亮

• FM-03: 触发器卡住，无法复位，或MOTOR持续运行

  FM-03 触发器卡住，无法回弹，或MOTOR持续运行

• FM-27: FM-27 工具或电池组过热，或热关闭重复发生

  FM-27 工具或电池组过热，或热关闭重复发生

• FM-24: 钻头或紧固件卡滞，工具停转、扭曲或卡住

  FM-24 钻头或紧固件卡滞，工具停转、扭曲或卡住

• FM-02: 工作灯亮，但 MOTOR 不启动

  FM-02 工作灯亮起，但MOTOR不启动