CMCD700C1

型号： CMCD700C1

亦称： CMCD700, V20 Drill/Driver, CMCD700C1

• Craftsman Cmcd700c1 Repair Manual

• 完好V20battery完全就位，方向按钮完全前推或后推，工具无motor声音、LED响应或卡盘动作。静止状态持续。

  一个完好的V20battery已完全就位，方向按钮已完全 1. 将方向按钮置中，移除battery，检查工具和电池包是否有液体、膨胀、裂纹、熔化或燃烧迹象。

• A compatible V20 battery starts onto the tool rails but binds before reaching the normal seated and latched position.

  A compatible V20 battery starts onto the tool rails but binds 1. Stop pushing and withdraw the binding battery straight off the rails without

• The collar moves normally, but the clutch ratchets before a suitable fastener reaches normal depth at appropriate settings, or it audibly slips when drill mode is correctly selected.

  The collar moves normally, but the clutch ratchets before a 1. Release the trigger at early ratcheting, remove the battery, and verify the collar is

• With the battery removed, the keyless chuck sleeve or jaws remain seized, or a clamped bit cannot be released by normal hand rotation.

  With the battery removed, the keyless chuck sleeve or jaws 1. Center the direction button, remove the battery, support the tool, and support any

• The drill sounds and rotates normally with no load, does not stall, overheat, slip, or vibrate abnormally, yet a corrected drilling or fastening task progresses much more slowly than expected.

  The drill sounds and rotates normally with no load, does not 1. Remove the battery and inspect or replace the bit before changing any tool

• 卡盘停止且移除battery后，顶端选择器无法完全移入档位1或档位2，即使手动转动卡盘以对齐齿轮。

  卡盘停止且拆下battery时，顶部选择器 1. 完全停止卡盘并拆下battery，然后操作速度选择器。

• With the battery removed, the clutch collar is physically stuck, cracked, excessively loose, or unable to align a numbered setting or drill mode with the index mark.

  With the battery removed, the clutch collar is physically stuck, 1. Remove the battery before turning or inspecting the mode/torque collar.

• 室温V20battery完全就位于带电批准充电器中，但未开始正常充电或电池包未显示充满指示。

  室温的V20battery已完全插入通电的批准充电器，但正常充电未开始或电池包未显示充满指示。

• The chuck jaws open and close normally, but a straight compatible bit rotates or pulls out during moderate drilling or driving.

  The chuck jaws open and close normally, but a straight 1. Release the trigger, remove the battery, and remove or catch the loose bit before

• The collar moves and holds a low numbered setting, but the clutch does not ratchet before a test fastener is overdriven in suitable scrap material.

  The collar moves and holds a low numbered setting, but the 1. Remove the battery and set up a matching fastener and sound driver bit in

• The chuck still rotates, but a new mechanical grind, knock, scrape, tight spot, or severe vibration remains with the bit removed and is not ordinary motor or brake sound.

  The chuck still rotates, but a new mechanical grind, knock, 1. Stop at the first new mechanical noise or severe vibration, remove the battery, and

• 钻/起子在确认的BATTERY下无法启动

  FM-01 钻/起子在确认的 FM-09 BATTERY运行时间远短于预期

• FM-01: 钻/起子在确认的BATTERY下无法启动

  即使安装了确认的、充满电的V20 battery且方向按钮完全前进或后退，钻/起子仍无法启动。无motor声音、LED活动或夹头运动，工具无响应。

• FM-17: 两速选择器无法在档位间切换

  Craftsman CMCD700C1 V20 1/2英寸钻/起子套装 - 带电刹车的有刷MOTOR - 两速 - 无钥匙卡盘 - LED灯

• FM-27: 工具出现新的磨擦、敲击、卡滞或严重振动

  FM-27

• FM-28: 尽管空载正常，钻孔或紧固仍然缓慢

  FM-28

• FM-23: 钻头在卡盘中滑动或被拉出。

  FM-23

• FM-20: 离合器从不释放且在低设置时过度驱动紧固件

  FM-20

• FM-25: 卡盘或钻头在空载时明显摆动

  卡盘或钻头在低速空载时表现出明显的侧向摆动或跳动，前提是钻头已正确居中并紧固。

• FM-15: 工具仅向一个方向运行或与选择方向相反

  工具的方向选择器动作正常并保持卡位，但卡盘仅向一个方向旋转或反向旋转。

• FM-22: 卡盘无法手动打开或关闭，或钻头无法释放

  卡盘无法手动打开或关闭，或钻头无法释放

• FM-16: 中心锁不阻止扳机动作

  FM-16

• FM-21: 离合器过早释放或在钻孔模式下打滑

  FM-22

• FM-06: 工具或BATTERY移动时断电

  移动依赖的断电。