GSR18V-190B22

型号： GSR18V-190B22

亦称： Bosch Power Tools, Bosch, GSR18V-190B22

• Bosch Gsr18v 190b22 Repair Manual
• Bosch Gsr18v 190b22 Repair Manual Ba37d883

• The chuck sleeve or jaws bind, fail to center, trap a bit, or cannot grip it.

  The chuck sleeve or jaws bind, fail to center, trap a bit, 1. Center-lock the trigger, remove the battery, and let the bit and chuck

• The battery will not slide in, lock, release, or remain secure in the handle.

  The battery will not slide in, lock, release, or remain 1. Support the drill, press the release, and slide the pack out without prying.

• The drill works at no load but stalls, slows severely, or stops during drilling or driving.

  The drill works at no load but stalls, slows severely, or 1. Release, wait for stop, center-lock, remove the battery, and free the bit.

• 钻机在已验证充电电池包下无电机、夹头或工作灯响应。

  钻机无 motor、夹头或工作灯响应 1. 中心锁定触发器，拆卸 battery，检查两组接触点。

• A bit that appears clamped slips in use or visibly wobbles in a no-load test.

  A bit that appears clamped slips in use or visibly 1. Center-lock the trigger, remove the battery, and discard any bent bit.

• The top selector sticks, will not stay in range, or low and high feel the same.

  The top selector sticks, will not stay in range, or low and 1. Set the drill down, release the trigger, wait for stop, center-lock, and

• The pack will not complete charging or delivers abnormally short light-duty runtime.

  The pack will not complete charging or delivers 1. Remove the pack, let it reach room temperature, and inspect the pack

• The chuck coasts much longer than normal after the trigger is released.

  The chuck coasts much longer than normal after the 1. Center-lock the trigger, remove the battery, and empty the chuck.

• The torque ring binds, will not hold a setting, or slips at clearly wrong torque.

  The torque ring binds, will not hold a setting, or slips at 1. Center-lock the trigger, remove the battery, and unload the chuck.

• The front work light stays dark during trigger use or remains on abnormally afterward.

  The front work light stays dark during trigger use or 1. Center-lock the trigger, remove the battery, and wipe the light window

• 电源断断续续或减弱，出现异常motor噪音，或brush火花过多。

  电源断断续续或减弱，异常的 motor 噪音 1. 中心锁定触发器，拆下 battery，让 motor 完全冷却。

• The trigger binds, the drill runs on, or no-load speed jumps instead of varying smoothly.

  The trigger binds, the drill runs on, or no-load speed 1. If it runs on, release it, center-lock the trigger, and remove the battery.

• FM-16: FM-16 出现烟雾、液体、膨胀、燃烧气味或重大损坏

  FM-16 出现烟雾、液体、膨胀、燃烧气味或重大损坏

• FM-05: FM-05 方向杆卡滞、选择错误或无法锁定关闭

  FM-05 方向杆卡滞、选择错误或无法锁定关闭

• FM-09: FM-09 无钥匙夹头爪无法打开、关闭、释放或夹紧

  FM-09 无钥匙夹头爪无法打开、关闭、释放或夹紧

• FM-15: FM-15 钻机磨损、敲击、振动或夹头松动

  FM-15 钻机磨损、敲击、振动或夹头松动

• FM-12: FM-12 钻机堵转、失去动力或负载停止

  FM-12 钻机堵转、失去动力或负载停止

• FM-06: FM-06 电动制动器无法快速停止夹头

  FM-06 电动制动器无法快速停止夹头

• FM-14: FM-14 内置工作灯不亮或持续点亮

  FM-14 内置工作灯不亮或持续点亮

• FM-13: FM-13 碳刷 BRUSHES 磨损、卡滞或严重电弧

  FM-13 碳刷 BRUSHES 磨损、卡滞或严重电弧

• FM-08: FM-08 离合环无法移动、保持或控制打滑

  FM-08 离合环无法移动、保持或控制打滑

• fm-p14-b-387bc595: 扭矩环卡滞，无法保持设定，或打滑。

  1. 居中锁定扳机，拆卸电机碳刷，卸载夹头。

• FM-10: FM-10 A 固定钻头打滑、晃动或空载偏摆

  FM-10 A 固定钻头打滑、晃动或空载偏摆

• FM-11: Fm-11 Motor运转但夹头不旋转

  Fm-11 Motor运转但夹头不旋转