CMCF800C1

型号： CMCF800C1

亦称： Craftsman, CMCF800C1

• Craftsman Cmcf800c1 Repair Manual

• TRIGGER STICKS, WILL NOT RETURN, OR MOTOR KEEPS RUNNING

  FM-03 TRIGGER STICKS, WILL NOT RETURN, OR MOTOR KEEPS RUNNING

• 工具完全死機 - 無LED或MOTOR

  FM-01 工具完全死機 - 冇LED或MOTOR FM-09 電源喺電池包或工具時斷斷續續

• The release button moves poorly or the pack remains trapped on the tool rails.

  The release button moves poorly or the pack remains 1. Center direction and support tool and pack so no weight binds the rails.

• The forward/reverse button will not seat, center lock-off fails, or the tool runs the wrong way.

  The forward/reverse button will not seat, center lock-off 1. Release the trigger, wait for full stop, and remove the pack.

• The trigger returns and motor power ends, but the chuck repeatedly coasts much longer than normal.

  The trigger returns and motor power ends, but the chuck 1. Remove the accessory, fit a charged known-good pack, and point safely.

• 已裝入充電電池包，但扳機無工作燈、motor聲音或鐵砧動作。

  已裝入充電battery電池包，但拉扳機無工作燈、motor聲音或鐵砧動作。

• A known-straight, fully retained 1/4-in. hex bit traces a visible circle at no load.

  A known-straight, fully retained 1/4-in. hex bit traces a 1. Remove the pack; inspect and clean a known-straight bit and its shank.

• 合格嘅衝擊等級1/4吋六角配件唔能完全插入或鎖定快速釋放夾頭。

  一個合格嘅衝擊等級 1/4 吋六角配件唔能 1. 將方向調正，拆出電池包，檢查配件柄部同凹槽。

• The tool starts and runs at no load, but stops abruptly on an ordinary fastener with no jam or twist.

  The tool starts and runs at no load, but stops abruptly 1. Release the trigger, remove the pack, and prove the fastener is not

• 無緊固負載時，速度波動、有死區、斷斷續續或忽略扳機行程。

  冇緊固件負載時，速度忽快忽慢，有死區，斷斷續續，或者忽略扳機行程。1. 拆除鑽頭，裝上已知良好電池組，做一次短暫無負載扳機掃描。

• The bit rotates, but a real fastening load never produces the normal impact sound or pulses.

  The bit rotates, but a real fastening load never produces 1. Fit a charged known-good pack and the correct impact-rated accessory.

• Bright repeated arcing or sharp crackling is visible at the rear vents while the tool runs.

  Bright repeated arcing or sharp crackling is visible at the 1. Release the trigger, remove the pack, and let the motor area cool.

• FM-22: 驅動輸出低，儘管旋轉同衝擊穩定

  FM-22 驅動輸出低，儘管旋轉同衝擊穩定

• FM-23: 緊固件打滑、剝落、斷裂或過度擰緊

  FM-23 緊固件打滑、脫牙、斷裂或者過度擰緊

• FM-29: 外殼、手柄、導軌、前端、通風口或掛鉤安裝損壞

  FM-29 外殼、手柄、導軌、前端、通風口或掛鉤安裝損壞

• FM-15: 正確嘅1/4吋六角批頭唔能插入或鎖定

  FM-15 A 正確嘅1/4吋六角批頭唔能插入或鎖定

• FM-09: 電池包或工具移動時電源中斷

  Fm-09 電源喺電池包或者工具移動時會斷電

• FM-25: FM-25 工具負載下關機，無機械卡住

  FM-25 工具負載下關機，無機械卡住

• FM-01: FM-01 工具完全死機 - 無LED或MOTOR

  儘管已裝入充電battery電池包，工具完全死機，無LED或motor反應。

• FM-13: 工作燈持續亮超過正常餘光時間

  FM-13 工作燈持續亮超過正常餘光時間

• FM-03: 扳機卡住，唔會回彈，或者MOTOR持續運行

  FM-03 扳機卡住，唔彈返，或者MOTOR繼續運行

• FM-27: FM-27 工具或電池包過熱，或者熱量熄火重複發生

  FM-27 工具或電池包過熱，或者熱量熄火重複發生

• FM-24: 批頭或緊固件卡住，工具停轉、扭曲或卡住

  FM-24 批頭或者緊固件卡住，工具停轉、扭曲或者卡住

• FM-02: 工作燈亮，但 MOTOR 唔會啟動

  FM-02 工作燈亮，但MOTOR唔啟動