GSR18V-190B22

型号： GSR18V-190B22

亦称： Bosch Power Tools, Bosch, GSR18V-190B22

• Bosch Gsr18v 190b22 Repair Manual
• Bosch Gsr18v 190b22 Repair Manual Ba37d883

• The chuck sleeve or jaws bind, fail to center, trap a bit, or cannot grip it.

  The chuck sleeve or jaws bind, fail to center, trap a bit, 1. Center-lock the trigger, remove the battery, and let the bit and chuck

• battery唔能滑入、鎖定、釋放或保持穩固喺手柄。

  battery唔會滑入、鎖定、釋放或者保持 1. 支撐鑽機，按住釋放，唔好撬開，直接滑出電池組。

• The drill works at no load but stalls, slows severely, or stops during drilling or driving.

  The drill works at no load but stalls, slows severely, or 1. Release, wait for stop, center-lock, remove the battery, and free the bit.

• 電鑽冇motor、夾頭或工作燈反應，即使用咗已知充滿電嘅battery。

  已證明嘅充電 motor。接觸組件。

• A bit that appears clamped slips in use or visibly wobbles in a no-load test.

  A bit that appears clamped slips in use or visibly 1. Center-lock the trigger, remove the battery, and discard any bent bit.

• The top selector sticks, will not stay in range, or low and high feel the same.

  The top selector sticks, will not stay in range, or low and 1. Set the drill down, release the trigger, wait for stop, center-lock, and

• 電池包唔能完成充電或運行時間異常短。

  電池組唔會完成充電或者提供 1. 拆除電池組，讓佢回到室溫，檢查電池組

• The chuck coasts much longer than normal after the trigger is released.

  The chuck coasts much longer than normal after the 1. Center-lock the trigger, remove the battery, and empty the chuck.

• The torque ring binds, will not hold a setting, or slips at clearly wrong torque.

  The torque ring binds, will not hold a setting, or slips at 1. Center-lock the trigger, remove the battery, and unload the chuck.

• The front work light stays dark during trigger use or remains on abnormally afterward.

  The front work light stays dark during trigger use or 1. Center-lock the trigger, remove the battery, and wipe the light window

• Power is sporadic or reduced, unusual motor noise appears, or brush sparking is excessive.

  Power is sporadic or reduced, unusual motor noise 1. Center-lock the trigger, remove the battery, and let the motor cool fully.

• The trigger binds, the drill runs on, or no-load speed jumps instead of varying smoothly.

  The trigger binds, the drill runs on, or no-load speed 1. If it runs on, release it, center-lock the trigger, and remove the battery.

• FM-16: FM-16 SMOKE, LIQUID, SWELLING, BURNING ODOR, OR MAJOR DAMAGE IS PRESENT

  FM-16 SMOKE, LIQUID, SWELLING, BURNING ODOR, OR MAJOR DAMAGE IS PRESENT

• FM-05: FM-05 方向桿卡住、選錯或者唔會鎖定關閉

  前後方向撥桿卡住，選錯方向，或者唔能鎖定喺中間OFF位置，導致控制唔正常。

• FM-09: FM-09 THE KEYLESS CHUCK JAWS WILL NOT OPEN, CLOSE, RELEASE, OR GRIP

  FM-09 THE KEYLESS CHUCK JAWS WILL NOT OPEN, CLOSE, RELEASE, OR GRIP

• FM-15: FM-15 THE DRILL GRINDS, KNOCKS, VIBRATES, OR HAS CHUCK PLAY

  FM-15 THE DRILL GRINDS, KNOCKS, VIBRATES, OR HAS CHUCK PLAY

• FM-12: FM-12 THE DRILL STALLS, LOSES POWER, OR STOPS UNDER LOAD

  FM-12 THE DRILL STALLS, LOSES POWER, OR STOPS UNDER LOAD

• FM-06: FM-06 電動剎車唔能快速停止夾頭

  釋放扳機後，電動剎車唔能快速停止夾頭，導致夾頭比正常情況轉得耐。

• FM-14: FM-14 THE BUILT-IN WORK LIGHT DOES NOT ILLUMINATE OR STAYS ON

  FM-14 THE BUILT-IN WORK LIGHT DOES NOT ILLUMINATE OR STAYS ON

• FM-13: FM-13 THE CARBON BRUSHES ARE WORN, STICKING, OR ARCING HEAVILY

  FM-13 THE CARBON BRUSHES ARE WORN, STICKING, OR ARCING HEAVILY

• FM-08: 扭力環卡住，唔能保持設定，或者喺明顯錯誤嘅扭力下打滑。

  置中鎖定扳機，拆除battery，卸載夾頭。

• fm-p14-b-387bc595: 扭力環卡住，唔能保持設定，或者打滑

  1. 置中鎖定扳機，拆除battery，卸載夾頭。

• FM-10: FM-10 A SECURED BIT SLIPS, WOBBLES, OR RUNS OUT AT NO LOAD

  FM-10 A SECURED BIT SLIPS, WOBBLES, OR RUNS OUT AT NO LOAD

• FM-11: FM-11 THE MOTOR RUNS BUT THE CHUCK DOES NOT ROTATE

  FM-11 THE MOTOR RUNS BUT THE CHUCK DOES NOT ROTATE