GKS18V-25, GKS18V-25N

型号： GKS18V-25, GKS18V-25N

亦称： Robert Bosch GmbH, GKS18V-25, GKS18V-25, GKS18V-25N

• Bosch Gks18v 25 Circular Saw Repair And Maintenance Manual Repair Manual

• The foot rocks on a flat surface, is bent or cracked, or moves despite locked adjustments.

  The foot rocks on a flat surface, is bent or cracked, or moves 1. Remove the battery and place the foot on a known-flat surface, inspecting from

• motor同軸轉動，但鋸片喺墊圈上停滯或滑動，喺正常支撐切割時。

  motor 同軸轉動，但鋸片喺正常有支撐嘅切割時停轉或者打滑。 1. 第一次打滑時放開扳機，等鋸片停低，拆除 motor。

• 裝咗正確嘅 battery，但按鎖定按鈕時同扳機冇產生任何 motor 反應。

  裝咗正確嘅 battery，但按鎖定按鈕同 1. 將鎖定設置為休息狀態，拆除 battery，檢查電池組同工具有冇熱、液體、裂紋或燒焦。

• No-load operation is smooth, but the saw bounces, chatters, or vibrates as soon as cutting begins.

  No-load operation is smooth, but the saw bounces, chatters, 1. Release the trigger, keep the foot flat until the blade stops, and remove the

• The external structure is visibly cracked, loose, crushed, melted, or missing material even if the saw still runs.

  The external structure is visibly cracked, loose, crushed, 1. Remove the battery and stop carrying or operating the saw until the complete

• The blade turns steadily, but wood cuts slowly, burns, or needs heavy feed pressure.

  The blade turns steadily, but wood cuts slowly, burns, or 1. Stop forcing the saw, let the blade stop, remove the battery, and inspect teeth for

• With the blade clear of material, the saw sounds slow, hunts, or repeatedly rises and falls in speed.

  With the blade clear of material, the saw sounds slow, hunts, 1. Remove the battery, inspect the blade and guards, and hand-turn the blade to feel

• The saw or pack smokes, leaks, sparks, melts, smells burned, swells, vents, or hisses.

  The saw or pack smokes, leaks, sparks, melts, smells burned, 1. Stop, move away from the hazard, and remove the battery only if it can be done

• 底座可以設定角度，但喺斜切桿鎖定後會移動或切割時漂移。

  腳可以設定角度，但喺斜角桿鎖緊後會移動或切割時漂移。1. 停止切割，拆除 battery，標記選定嘅斜角位置。

• 360度塵口塞住或者鬆脫，或者兼容嘅喉管/接頭唔會保持連接。

  360度塵口卡住或者鬆脫，或者兼容嘅

• 鎖定0度斜切時，聲音正常嘅鋸片唔係正方形對齊底座。

  喺鎖定嘅 0 度斜角，聲音正常嘅刀片唔垂直於腳。1. 拆除 battery，確認已知直嘅刀片正確安裝，腳睇落正常。

• A suitable bag or vacuum collects little dust while the port remains secure and aimed.

  A suitable bag or vacuum collects little dust while the port 1. Remove the battery, detach the bag or hose, and clear dry chips from the

• FM-08: FM-08 無負載轉速弱、唔均勻或者波動

  FM-08 無負載轉速弱、唔均勻或者波動

• FM-07: FM-07 扳機卡住或MOTOR喺鬆開後繼續運轉

  扳機卡住或motor喺鬆開扳機後繼續運轉，原因係開關或扳機機構故障。

• FM-01: FM-01 工具完全無反應 - 無MOTOR反應

  當扳機被按下時，工具完全無反應，無motor反應，即使battery正確安裝。

• FM-37: FM-37 機殼、手柄、BATTERY導軌或者通風口有裂紋或者損壞

  FM-37 機殼、手柄、BATTERY導軌或者通風口有裂紋或者損壞

• fm-p17-b-2db8b3a0: 兼容嘅battery無法完全插入機殼或會...

  1. 拆除battery，檢查整條導軌同卡扣路徑，然後...

• fm-p29-b-beec475a: The selected depth will not remain fixed after the depth lever is

  1. Stop cutting, remove the battery, and mark the current depth position on the scale.

• FM-24: FM-24 下護罩無法及時關閉

  FM-29 斜切設定滑動或無法保持...

• FM-38: FM-38 冒煙、燒焦味、熔化、液體、火花或者BATTERY損壞

  鋸或battery出現冒煙、燒焦味、熔化、液體滲漏、火花、膨脹、通風或其他嚴重損壞跡象。

• FM-06: FM-06 鎖定釋放掣無法阻擋扳機或回復原位

  FM-06 鎖定釋放掣無法阻擋扳機或回復原位

• FM-27: 所選深度喺深度桿鬆開後無法保持固定

  停止切割，拆除battery，標記當前深度位置 FM-27

• FM-04: battery卡喺鋸入面，無法取出

  支撐battery，按下釋放掣，只向前滑動到次級...

• FM-33: FM-33 塵口唔會轉動、保持位置或者固定喉管

  FM-33 塵口唔會轉動、保持位置或者固定喉管