Triệu chứng
Duyệt triệu chứng đã ghi nhận và chuyển đến hướng dẫn sửa chữa phù hợp từ kết quả tìm kiếm.
The robot stops with Error 68 because its camera failed during the cleaning job.
0 hướng dẫn liên quan
Tìm hướng dẫn →
The drill runs steadily but drills slowly or cannot drive a normal fastener with correct setup.
0 hướng dẫn liên quan
Tìm hướng dẫn →
The robot reports four beeps immediately after an attempted start.
0 hướng dẫn liên quan
Tìm hướng dẫn →
The app reports Error 21, 25, 34, 38, 39, 47, 66, or 76 and the robot cannot reliably continue.
0 hướng dẫn liên quan
Tìm hướng dẫn →
The robot stops and reports five beeps while wedged or unable to escape.
0 hướng dẫn liên quan
Tìm hướng dẫn →
The bit jams, the motor stalls, or the drill twists sharply in the hands during work.
0 hướng dẫn liên quan
Tìm hướng dẫn →
The running saw jumps, vibrates against the work, snags, or kicks backward or sideways.
0 hướng dẫn liên quan
Tìm hướng dẫn →
A genuine m Series pad is fully seated in both tracks, but the robot refuses to run or selects the wrong pad state.
0 hướng dẫn liên quan
Tìm hướng dẫn →
With the battery removed and no bit fitted, the chuck will not hand-turn normally or feels seized.
0 hướng dẫn liên quan
Tìm hướng dẫn →
After the trigger is released, the blade keeps stroking noticeably longer than normal.
0 hướng dẫn liên quan
Tìm hướng dẫn →
The robot stops with a drive wheel hanging over a step or threshold and reports six beeps.
0 hướng dẫn liên quan
Tìm hướng dẫn →
With a secure known-good blade clear of the work, the saw has harsh sound, bind, or vibration.
0 hướng dẫn liên quan
Tìm hướng dẫn →
The robot stops and reports eight beeps because its wheels cannot turn.
0 hướng dẫn liên quan
Tìm hướng dẫn →
A secure straight bit and clear work do not eliminate harsh no-load sound or vibration.
0 hướng dẫn liên quan
Tìm hướng dẫn →
A correct m Series pad binds in the tracks, will not seat flat, or will not release when the eject button is pressed.
0 hướng dẫn liên quan
Tìm hướng dẫn →
The robot reports ten beeps after the distress sound.
0 hướng dẫn liên quan
Tìm hướng dẫn →
The tool, pack, or charger becomes unusually hot, or protection repeatedly stops operation.
0 hướng dẫn liên quan
Tìm hướng dẫn →
The tank is filled to the top and installed flat, but the red sweep or Error 37 still says to fill it.
0 hướng dẫn liên quan
Tìm hướng dẫn →
The saw, battery, or charger becomes abnormally hot or repeatedly shuts down after warming.
0 hướng dẫn liên quan
Tìm hướng dẫn →
The robot repeatedly reverses, circles, turns in place, or drifts instead of following a stable path.
0 hướng dẫn liên quan
Tìm hướng dẫn →